Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairKitchenAid Refrigerator Dispenser User Interface Replacement W11405309 
KitchenAid Refrigerator Dispenser User Interface Replacement W11405309
Skill Level
Total Parts Cost
$216.49Estimated Savings
$112.5002:40
- Description
This video provides step-by-step repair instructions for replacing the dispenser user interface on a KitchenAid Refrigerator (Model KRFF507HPS02). The most common reason for replacing this part is if the dispenser is not functioning at all.
All of the information for this video is applicable to the following brands: KitchenAid
All of the information for this video is applicable to the following brands: KitchenAid
Step By Step Instructions
1
To replace the dispenser user interface assembly in this kitchenaid refrigerator, you will need two thin putty knives and painter’s tape.
2
Before you begin the procedure, unplug the appliance’s power cord.
3
Apply a strip of painter’s tape directly below the dispenser interface, as well as along the left edge.
4
Now insert the two thin putty knives to pry the left side and botom of the interface away from the door and you can then pull the top edge free.
5
Slide out the retaining clips securing the actuator paddle wire connecters, then disconnect all five wire connecters to fully remove the old interface.
6
To install the new dispenser user interface assembly, first connect the wire connecters to the appropriate terminals.
7
Secure the actuator paddle wire connecters with the retaining clips.
8
Insert the upper tabs on the interface into the slots in the housing then snap the bottom into place.
9
Remove the tape.
10
Plug the power cord back in, and the refrigerator should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the dispenser user interface on a KitchenAid Refrigerator (Model KRFF507HPS02). The most common reason for replacing this part is if the dispenser is not functioning at all.
All of the information for this video is applicable to the following brands: KitchenAid
All of the information for this video is applicable to the following brands: KitchenAid
Step-By-Step Instructions
1
To replace the dispenser user interface assembly in this kitchenaid refrigerator, you will need two thin putty knives and painter’s tape.
2
Before you begin the procedure, unplug the appliance’s power cord.
3
Apply a strip of painter’s tape directly below the dispenser interface, as well as along the left edge.
4
Now insert the two thin putty knives to pry the left side and botom of the interface away from the door and you can then pull the top edge free.
5
Slide out the retaining clips securing the actuator paddle wire connecters, then disconnect all five wire connecters to fully remove the old interface.
6
To install the new dispenser user interface assembly, first connect the wire connecters to the appropriate terminals.
7
Secure the actuator paddle wire connecters with the retaining clips.
8
Insert the upper tabs on the interface into the slots in the housing then snap the bottom into place.
9
Remove the tape.
10
Plug the power cord back in, and the refrigerator should be ready for use.
Applicable Product Model
Parts Needed
Control Board
$216.49
Total$0.00
Related Articles & Videos
02:47
Part Replacement
KitchenAid Refrigerator Lower Freezer Drawer Replacement W10594047
10:40
Part Replacement
KitchenAid Refrigerator Evaporator Fan Motor Replacement W11224591
04:12
Part Replacement
KitchenAid Refrigerator Upper Access Panel LED Light Assembly Replacement W11484839
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com