Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairKitchenAid Refrigerator Evaporator Fan Motor Grommet Replacement W11249950 
KitchenAid Refrigerator Evaporator Fan Motor Grommet Replacement W11249950
Skill Level
Total Parts Cost
$10.49Estimated Savings
$112.5009:34
- Description
This video provides step-by-step repair instructions for replacing the evaporator fan motor grommet on a KitchenAid Refrigerator (Model KRFF507HPS02). The most common reason for replacing this part is if the motor is loud.
All of the information for this video is applicable to the following brands: KitchenAid
All of the information for this video is applicable to the following brands: KitchenAid
Step By Step Instructions
1
To replace the evaporator fan motor grommet in this kitchenaid refrigerator, you will need a flat-head screwdriver, a small flat-head screwdriver, a quarter-inch nut driver, a magnetized quarter-inch nut driver, and needle-nose pliers.
2
Before you begin the procedure, unplug the appliance’s power cord.
3
Open the freezer drawer, and use the small flat-head screwdriver to pry the left slide rail tab away from the liner enough to release the drawer stop.
4
Do the same to release the right drawer stop.
5
With the stops out, you can fully remove the upper drawer.
6
Next, use the quarter-inch nut driver to loosen the two screws securing the drawer front.
7
Lift the drawer front off the drawer glides and set it aside.
8
You can now lift the lower drawer up and squeeze the sides in to release it from the glides.
9
Use the flat-head screwdriver to help pry apart the retainer clip so you can slide it to the left.
10
You can now lift the shaft up and out.
11
Using the flat-head screwdriver, depress the three retaining tabs inward to release the freezer outlet duct.
12
Depress the retaining tab to release the temperature sensor cover from the panel.
13
Detach the sensor from the cover.
14
Using the quarter-inch nut driver, unthread the four screws securing the evaporator access panel.
15
Set the access panel aside.
16
Use the magnetized quarter-inch nut driver to unthread the two screws securing the evaporator fan motor housing to the rear liner.
17
Pull the housing forward and disconnect the two upper wire harness connecters.
18
You will now need to detach the two grounding clips, disconnect the two defrost heater wire connecters, then detach the defrost thermostat from the evaporator coil to fully remove the assembly.
19
Pull the fan blade off of the motor shaft.
20
Depress the tabs to release the motor retaining bracket.
21
You can now detach the evaporator fan motor and remove the old grommet.
22
To install the new evaporator fan motor grommet, align it on the motor shaft and the rear of the motor.
23
Reposition the motor and snap the retaining bracket into place to secure.
24
Confirm the foam insulators are in place, then realign the fan blade on the motor shaft.
25
Reinstall the assembly by first snapping the defrost thermostat onto the evaporator coil.
26
Connect the two defrost heater wire connecters, as well as the two upper wire harness connecters.
27
Attach the two grounding clips to the evaporator housing.
28
Now position the evaporator fan motor housing, and rethread the two screws to secure.
29
Partially reposition the access panel, making sure the sensor wire is seated in the upper left notch.
30
Fully position the panel and rethread the four screws to secure.
31
Snap the sensor into place in the cover, then align and snap the cover into place on the access panel.
32
Realign the outelt duct on the panel and snap it into place.
33
Confirm the shaft retainer clip is on the shaft.
34
With the glides pushed all the way in, insert the left end of the shaft into the left side gear.
35
Position the right end of the shaft in the right-side gear and snap the retainer clip into place to secure.
36
Reinstall the drawer by aligning it on the glides, making sure the rear hooks are secured under the glide, then set the drawer in place.
37
Reposition the drawer front on the glides, and tighten the screws.
38
Reinstall the upper freezer drawer by, aligning the rear rollers on the track and the front rollers on the lower drawer then push the drawer in.
39
Snap both drawer stops into place to secure.
40
Plug the power cord back in, and the refrigerator should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the evaporator fan motor grommet on a KitchenAid Refrigerator (Model KRFF507HPS02). The most common reason for replacing this part is if the motor is loud.
All of the information for this video is applicable to the following brands: KitchenAid
All of the information for this video is applicable to the following brands: KitchenAid
Step-By-Step Instructions
1
To replace the evaporator fan motor grommet in this kitchenaid refrigerator, you will need a flat-head screwdriver, a small flat-head screwdriver, a quarter-inch nut driver, a magnetized quarter-inch nut driver, and needle-nose pliers.
2
Before you begin the procedure, unplug the appliance’s power cord.
3
Open the freezer drawer, and use the small flat-head screwdriver to pry the left slide rail tab away from the liner enough to release the drawer stop.
4
Do the same to release the right drawer stop.
5
With the stops out, you can fully remove the upper drawer.
6
Next, use the quarter-inch nut driver to loosen the two screws securing the drawer front.
7
Lift the drawer front off the drawer glides and set it aside.
8
You can now lift the lower drawer up and squeeze the sides in to release it from the glides.
9
Use the flat-head screwdriver to help pry apart the retainer clip so you can slide it to the left.
10
You can now lift the shaft up and out.
11
Using the flat-head screwdriver, depress the three retaining tabs inward to release the freezer outlet duct.
12
Depress the retaining tab to release the temperature sensor cover from the panel.
13
Detach the sensor from the cover.
14
Using the quarter-inch nut driver, unthread the four screws securing the evaporator access panel.
15
Set the access panel aside.
16
Use the magnetized quarter-inch nut driver to unthread the two screws securing the evaporator fan motor housing to the rear liner.
17
Pull the housing forward and disconnect the two upper wire harness connecters.
18
You will now need to detach the two grounding clips, disconnect the two defrost heater wire connecters, then detach the defrost thermostat from the evaporator coil to fully remove the assembly.
19
Pull the fan blade off of the motor shaft.
20
Depress the tabs to release the motor retaining bracket.
21
You can now detach the evaporator fan motor and remove the old grommet.
22
To install the new evaporator fan motor grommet, align it on the motor shaft and the rear of the motor.
23
Reposition the motor and snap the retaining bracket into place to secure.
24
Confirm the foam insulators are in place, then realign the fan blade on the motor shaft.
25
Reinstall the assembly by first snapping the defrost thermostat onto the evaporator coil.
26
Connect the two defrost heater wire connecters, as well as the two upper wire harness connecters.
27
Attach the two grounding clips to the evaporator housing.
28
Now position the evaporator fan motor housing, and rethread the two screws to secure.
29
Partially reposition the access panel, making sure the sensor wire is seated in the upper left notch.
30
Fully position the panel and rethread the four screws to secure.
31
Snap the sensor into place in the cover, then align and snap the cover into place on the access panel.
32
Realign the outelt duct on the panel and snap it into place.
33
Confirm the shaft retainer clip is on the shaft.
34
With the glides pushed all the way in, insert the left end of the shaft into the left side gear.
35
Position the right end of the shaft in the right-side gear and snap the retainer clip into place to secure.
36
Reinstall the drawer by aligning it on the glides, making sure the rear hooks are secured under the glide, then set the drawer in place.
37
Reposition the drawer front on the glides, and tighten the screws.
38
Reinstall the upper freezer drawer by, aligning the rear rollers on the track and the front rollers on the lower drawer then push the drawer in.
39
Snap both drawer stops into place to secure.
40
Plug the power cord back in, and the refrigerator should be ready for use.
Applicable Product Model
Parts Needed
Grommet
$10.49
Total$0.00
Related Articles & Videos
02:47
Part Replacement
KitchenAid Refrigerator Lower Freezer Drawer Replacement W10594047
10:40
Part Replacement
KitchenAid Refrigerator Evaporator Fan Motor Replacement W11224591
04:12
Part Replacement
KitchenAid Refrigerator Upper Access Panel LED Light Assembly Replacement W11484839
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com