Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairKitchenAid Refrigerator Power Cord Replacement W11254160 
This video provides step-by-step repair instructions for replacing the power cord on a KitchenAid Refrigerator (Model KRFF507HPS02). The most common reason for replacing this part is if the refrigerator will not turn on.
All of the information for this video is applicable to the following brands: KitchenAid
KitchenAid Refrigerator Power Cord Replacement W11254160
Skill Level
Total Parts Cost
$118.26Estimated Savings
$112.5007:02
- Description
This video provides step-by-step repair instructions for replacing the power cord on a KitchenAid Refrigerator (Model KRFF507HPS02). The most common reason for replacing this part is if the refrigerator will not turn on.
All of the information for this video is applicable to the following brands: KitchenAid
Step By Step Instructions
1
To replace the power cord on this kitchenaid refrigerator, you will need a quarter-inch nut driver, a quarter-inch wrench, an adjustable wrench, and zip-ties.
2
Before you begin the procedure, make sure the old power cord is unplugged.
3
Shut off the home’s water supply line valve.
4
To move the refrigerator away from the wall, first open the freezer drawer and pull the toe kick plate forward to remove.
5
Now use the quarter-inch wrench to rotate the brake feet counter-clockwise to raise them.
6
You can now roll the appliance forward.
7
Use the adjustable wrench to unthread the compression nut to detach the home’s water supply line from the inlet valve – be prepared for some water to spill.
8
Next, use the quarter-inch nut driver to unthread the nine screws securing the lower rear access panel.
9
With the screws unthreaded, detach the power cord strain relief from the panel and set the panel aside.
10
Next, disconnect the wire connecter from the water inlet valve.
11
Release the wires from the retaining hook and disconnect the condenser fan motor wire connecter.
12
Again, release the wires from the retaining hooks, and use the quarter-inch nut driver to unthread the screw to release the grounding wire from the frame.
13
Detach the second grounding wire from the compressor… and disconnect the start relay wire connecter.
14
Pull down the insulating sleeve and disconnect the main power cord wire connecter to fully remove the old component.
15
To prepare the new power cord for installation, transfer the insulating sleeve from the old cord to the new one.
16
You can use a zip-tie to secure it.
17
Now connect the main wire connecter and push up the sleeve.
18
Connect the start relay wire connecter, and attach the compressor grounding wire.
19
Secure the second grounding wire to the frame with the screw.
20
Secure the wires under the two retaining hooks.
21
Connect the condenser fan motor wire connecter.
22
Seat the wire in the notch in the fan housing, then secure the wires under the retaining hook, connect the water inlet valve wire connecter.
23
Reinstall the lower rear access panel by first sliding the right side behind the water filter supply line so the line is seated in the notch in the panel.
24
Seat the power cord strain relief in the panel notch, then fully reposition the panel, and thread the nine screws to secure.
25
Remember to secure the water filter supply line’s retainer with the top right screw.
26
Reattach the water supply line to the inlet valve by threading the compression nut – avoid overtightening the nut.
27
Push the refrigerator back against the wall, and lower the brake feet until they are in contact with the floor.
28
Replace the toe kick plate by aligning it on the lower frame and snapping it into place.
29
Turn the water supply back on, plug the new power cord in, and the refrigerator should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the power cord on a KitchenAid Refrigerator (Model KRFF507HPS02). The most common reason for replacing this part is if the refrigerator will not turn on.
All of the information for this video is applicable to the following brands: KitchenAid
This video provides step-by-step repair instructions for replacing the power cord on a KitchenAid Refrigerator (Model KRFF507HPS02). The most common reason for replacing this part is if the refrigerator will not turn on.
All of the information for this video is applicable to the following brands: KitchenAid
Step-By-Step Instructions
1
To replace the power cord on this kitchenaid refrigerator, you will need a quarter-inch nut driver, a quarter-inch wrench, an adjustable wrench, and zip-ties.
2
Before you begin the procedure, make sure the old power cord is unplugged.
3
Shut off the home’s water supply line valve.
4
To move the refrigerator away from the wall, first open the freezer drawer and pull the toe kick plate forward to remove.
5
Now use the quarter-inch wrench to rotate the brake feet counter-clockwise to raise them.
6
You can now roll the appliance forward.
7
Use the adjustable wrench to unthread the compression nut to detach the home’s water supply line from the inlet valve – be prepared for some water to spill.
8
Next, use the quarter-inch nut driver to unthread the nine screws securing the lower rear access panel.
9
With the screws unthreaded, detach the power cord strain relief from the panel and set the panel aside.
10
Next, disconnect the wire connecter from the water inlet valve.
11
Release the wires from the retaining hook and disconnect the condenser fan motor wire connecter.
12
Again, release the wires from the retaining hooks, and use the quarter-inch nut driver to unthread the screw to release the grounding wire from the frame.
13
Detach the second grounding wire from the compressor… and disconnect the start relay wire connecter.
14
Pull down the insulating sleeve and disconnect the main power cord wire connecter to fully remove the old component.
15
To prepare the new power cord for installation, transfer the insulating sleeve from the old cord to the new one.
16
You can use a zip-tie to secure it.
17
Now connect the main wire connecter and push up the sleeve.
18
Connect the start relay wire connecter, and attach the compressor grounding wire.
19
Secure the second grounding wire to the frame with the screw.
20
Secure the wires under the two retaining hooks.
21
Connect the condenser fan motor wire connecter.
22
Seat the wire in the notch in the fan housing, then secure the wires under the retaining hook, connect the water inlet valve wire connecter.
23
Reinstall the lower rear access panel by first sliding the right side behind the water filter supply line so the line is seated in the notch in the panel.
24
Seat the power cord strain relief in the panel notch, then fully reposition the panel, and thread the nine screws to secure.
25
Remember to secure the water filter supply line’s retainer with the top right screw.
26
Reattach the water supply line to the inlet valve by threading the compression nut – avoid overtightening the nut.
27
Push the refrigerator back against the wall, and lower the brake feet until they are in contact with the floor.
28
Replace the toe kick plate by aligning it on the lower frame and snapping it into place.
29
Turn the water supply back on, plug the new power cord in, and the refrigerator should be ready for use.
Applicable Product Model
Parts Needed
Power Cord
$118.26
Total$0.00
Related Articles & Videos
02:47
Part Replacement
KitchenAid Refrigerator Lower Freezer Drawer Replacement W10594047
10:40
Part Replacement
KitchenAid Refrigerator Evaporator Fan Motor Replacement W11224591
04:12
Part Replacement
KitchenAid Refrigerator Upper Access Panel LED Light Assembly Replacement W11484839
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com