Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairKitchenAid Refrigerator Water Inlet Valve Replacement W11482025 
This video provides step-by-step repair instructions for replacing the water inlet valve on a KitchenAid Refrigerator (Model KRFF507HPS02). The most common reason for replacing this part is if no ice is being made and no water is dispensing.
All of the information for this video is applicable to the following brands: KitchenAid
KitchenAid Refrigerator Water Inlet Valve Replacement W11482025
Skill Level
Total Parts Cost
$125.03Estimated Savings
$112.5005:24
- Description
This video provides step-by-step repair instructions for replacing the water inlet valve on a KitchenAid Refrigerator (Model KRFF507HPS02). The most common reason for replacing this part is if no ice is being made and no water is dispensing.
All of the information for this video is applicable to the following brands: KitchenAid
Step By Step Instructions
1
To replace the water inlet valve in this kitchenaid refrigerator, you will need a quarter-inch nut driver, a quarter-inch wrench, an adjustable wrench, and a 7/16th inch wrench.
2
Before you begin the procedure, unplug the appliance’s power cord.
3
Shut off the home’s water supply line valve.
4
To move the refrigerator away from the wall, first open the freezer drawer and pull the toe kick plate forward to remove.
5
Now use the quarter-inch wrench to rotate the brake feet counter-clockwise to raise them.
6
You can now roll the appliance forward.
7
Use the adjustable wrench to unthread the compression nut to detach the home’s water supply line from the inlet valve – be prepared for some water to spill.
8
Next, use the quarter-inch nut driver to unthread the nine screws securing the lower rear access panel.
9
With the screws unthreaded, detach the power cord strain relief from the panel and set the panel aside.
10
Using the quarter-inch nut driver, unthread the two screws to release the water inlet valve mounting bracket from the frame.
11
Disconnect the wire connecter from the valve.
12
Use the 7/16th inch wrench to depress the retaining ring to release the water filter supply line.
13
To install the new water inlet valve, first fully insert the water filter supply line into the valve port, then connect the wire connecter.
14
Align the mounting bracket on the frame and thread the two screws to secure.
15
Reinstall the lower rear access panel by first sliding the right side behind the water filter supply line so the line is seated in the notch in the panel.
16
Seat the power cord strain relief in the panel notch, then fully reposition the panel, and thread the nine screws to secure.
17
Remember to secure the water filter supply line’s retainer with the top right screw.
18
Reattach the water supply line to the inlet valve by threading the compression nut – avoid overtightening the nut.
19
Push the refrigerator back against the wall, and lower the brake feet until they are in contact with the floor.
20
Replace the toe kick plate by aligning it on the lower frame and snapping it into place.
21
Turn the water supply back on, plug the power cord back in, and the refrigerator should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the water inlet valve on a KitchenAid Refrigerator (Model KRFF507HPS02). The most common reason for replacing this part is if no ice is being made and no water is dispensing.
All of the information for this video is applicable to the following brands: KitchenAid
This video provides step-by-step repair instructions for replacing the water inlet valve on a KitchenAid Refrigerator (Model KRFF507HPS02). The most common reason for replacing this part is if no ice is being made and no water is dispensing.
All of the information for this video is applicable to the following brands: KitchenAid
Step-By-Step Instructions
1
To replace the water inlet valve in this kitchenaid refrigerator, you will need a quarter-inch nut driver, a quarter-inch wrench, an adjustable wrench, and a 7/16th inch wrench.
2
Before you begin the procedure, unplug the appliance’s power cord.
3
Shut off the home’s water supply line valve.
4
To move the refrigerator away from the wall, first open the freezer drawer and pull the toe kick plate forward to remove.
5
Now use the quarter-inch wrench to rotate the brake feet counter-clockwise to raise them.
6
You can now roll the appliance forward.
7
Use the adjustable wrench to unthread the compression nut to detach the home’s water supply line from the inlet valve – be prepared for some water to spill.
8
Next, use the quarter-inch nut driver to unthread the nine screws securing the lower rear access panel.
9
With the screws unthreaded, detach the power cord strain relief from the panel and set the panel aside.
10
Using the quarter-inch nut driver, unthread the two screws to release the water inlet valve mounting bracket from the frame.
11
Disconnect the wire connecter from the valve.
12
Use the 7/16th inch wrench to depress the retaining ring to release the water filter supply line.
13
To install the new water inlet valve, first fully insert the water filter supply line into the valve port, then connect the wire connecter.
14
Align the mounting bracket on the frame and thread the two screws to secure.
15
Reinstall the lower rear access panel by first sliding the right side behind the water filter supply line so the line is seated in the notch in the panel.
16
Seat the power cord strain relief in the panel notch, then fully reposition the panel, and thread the nine screws to secure.
17
Remember to secure the water filter supply line’s retainer with the top right screw.
18
Reattach the water supply line to the inlet valve by threading the compression nut – avoid overtightening the nut.
19
Push the refrigerator back against the wall, and lower the brake feet until they are in contact with the floor.
20
Replace the toe kick plate by aligning it on the lower frame and snapping it into place.
21
Turn the water supply back on, plug the power cord back in, and the refrigerator should be ready for use.
Applicable Product Model
Parts Needed
Water Inlet Valve
$125.03
Total$0.00
Related Articles & Videos
02:47
Part Replacement
KitchenAid Refrigerator Lower Freezer Drawer Replacement W10594047
10:40
Part Replacement
KitchenAid Refrigerator Evaporator Fan Motor Replacement W11224591
04:12
Part Replacement
KitchenAid Refrigerator Upper Access Panel LED Light Assembly Replacement W11484839
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com