Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairLG Washer Drain Pump Harness Replacement EAD64545811
This video provides step-by-step repair instructions for replacing the drain pump harness in an LG washer (Model WM4000HBA). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
LG
Don't forget to like and comment on this video and subscribe to our channel!
LG Washer Drain Pump Harness Replacement EAD64545811
Skill Level
Total Parts Cost
$53.20Estimated Savings
$112.5008:33
- Description
This video provides step-by-step repair instructions for replacing the drain pump harness in an LG washer (Model WM4000HBA). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
LG
Don't forget to like and comment on this video and subscribe to our channel!
Step By Step Instructions
1
To replace the drain pump harness in your lg washer, you will need needle nose pliers, zip ties, wire cutters, a spring removal tool, and a drill driver with a phillips bit.
2
Before you begin the procedure, unplug the washer.
3
Pull the washer away from the wall.
4
Unthread the two screws on the top panel.
5
Slide and lift the panel off.
6
Unthread the screw securing the right side of the control panel.
7
Open the drawer and push down on the “push” tab and remove the detergent assembly.
8
Unthread the two screws that secure the left side of the control panel.
9
Pry the three tabs then pull back and lift up to free the control panel.
10
Unplug the harness to the control panel.
11
Open the drain clean-out door.
12
Unclip the drain hose then unthread the two phillips screws.
13
Pull out the case.
14
Unthread the screw under the drain pump clean-out.
15
Use the spring removal tool or needle nose pliers to remove the retaining ring.
16
Detach the boot seal from the front panel.
17
Unthread the six screws on the front panel.
18
Push the panel down to release it from the tab.
19
Unplug the door lock from the harness.
20
Lift the front panel up and away from the washer.
21
Cut the zip tie securing the drain pump harness.
22
Uncover and detatch the plug.
23
Remove the two plugs from the pump and remove the harness.
24
To install the new drain pump harness, plug in the blue and white wires on the left side of the pump.
25
Plug the orange, yellow, and black wires on the right side of the pump.
26
Run the wires through the wire guides and plug in the main harness.
27
Cover the plugs with the plastic and secure with a zip tie.
28
Set the panel on the three tabs and plug in the door lock.
29
Push the panel upright and lock it in place with the tab.
30
Rethread the six screws into the panel.
31
Rethread the screw underneath the drain pump clean-out.
32
Feed the drain hose through the case and place in the washer.
33
Rethread the two phillips screws and clip in the drain hose.
34
Tuck the boot seal into the front panel.
35
Tuck the ring into the boot starting at the top.
36
Use the spring removal tool or needle nose pliers to insert the ring and securely seat it into the seal.
37
Plug the wire harness back into the display board.
38
Insert the control panel into its grooves and push forward to snap in place, rethread the two screws on the left side of the control panel.
39
Align the detergent assembly and push in until it snaps into place.
40
Rethread the screw on the right side of the control panel.
41
Set and slide the top panel onto the washer.
42
Rethread the two screws into the panel.
43
Push the washer back into place.
44
Plug the power cord back in, and your washer should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the drain pump harness in an LG washer (Model WM4000HBA). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
LG
Don't forget to like and comment on this video and subscribe to our channel!
This video provides step-by-step repair instructions for replacing the drain pump harness in an LG washer (Model WM4000HBA). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
LG
Don't forget to like and comment on this video and subscribe to our channel!
Step-By-Step Instructions
1
To replace the drain pump harness in your lg washer, you will need needle nose pliers, zip ties, wire cutters, a spring removal tool, and a drill driver with a phillips bit.
2
Before you begin the procedure, unplug the washer.
3
Pull the washer away from the wall.
4
Unthread the two screws on the top panel.
5
Slide and lift the panel off.
6
Unthread the screw securing the right side of the control panel.
7
Open the drawer and push down on the “push” tab and remove the detergent assembly.
8
Unthread the two screws that secure the left side of the control panel.
9
Pry the three tabs then pull back and lift up to free the control panel.
10
Unplug the harness to the control panel.
11
Open the drain clean-out door.
12
Unclip the drain hose then unthread the two phillips screws.
13
Pull out the case.
14
Unthread the screw under the drain pump clean-out.
15
Use the spring removal tool or needle nose pliers to remove the retaining ring.
16
Detach the boot seal from the front panel.
17
Unthread the six screws on the front panel.
18
Push the panel down to release it from the tab.
19
Unplug the door lock from the harness.
20
Lift the front panel up and away from the washer.
21
Cut the zip tie securing the drain pump harness.
22
Uncover and detatch the plug.
23
Remove the two plugs from the pump and remove the harness.
24
To install the new drain pump harness, plug in the blue and white wires on the left side of the pump.
25
Plug the orange, yellow, and black wires on the right side of the pump.
26
Run the wires through the wire guides and plug in the main harness.
27
Cover the plugs with the plastic and secure with a zip tie.
28
Set the panel on the three tabs and plug in the door lock.
29
Push the panel upright and lock it in place with the tab.
30
Rethread the six screws into the panel.
31
Rethread the screw underneath the drain pump clean-out.
32
Feed the drain hose through the case and place in the washer.
33
Rethread the two phillips screws and clip in the drain hose.
34
Tuck the boot seal into the front panel.
35
Tuck the ring into the boot starting at the top.
36
Use the spring removal tool or needle nose pliers to insert the ring and securely seat it into the seal.
37
Plug the wire harness back into the display board.
38
Insert the control panel into its grooves and push forward to snap in place, rethread the two screws on the left side of the control panel.
39
Align the detergent assembly and push in until it snaps into place.
40
Rethread the screw on the right side of the control panel.
41
Set and slide the top panel onto the washer.
42
Rethread the two screws into the panel.
43
Push the washer back into place.
44
Plug the power cord back in, and your washer should be ready for use.
Applicable Product Model
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com