Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairLG Washer Drain Bellow Assembly Replacement AAS73169401
This video provides step-by-step repair instructions for replacing the drain bellow assembly in an LG washer (Model WM4000HBA). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
LG
Don't forget to like and comment on this video and subscribe to our channel!
LG Washer Drain Bellow Assembly Replacement AAS73169401
Skill Level
Total Parts Cost
$101.53Estimated Savings
$112.5007:18
- Description
This video provides step-by-step repair instructions for replacing the drain bellow assembly in an LG washer (Model WM4000HBA). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
LG
Don't forget to like and comment on this video and subscribe to our channel!
Step By Step Instructions
1
To replace the drain bellow assembly in your lg washer, you will need a short phillips screwdriver, channellock pliers, and a drill driver with a phillips bit.
2
Before you begin the procedure, unplug the washer.
3
Turn off the water supply.
4
Pull the washer away from the wall.
5
Unthread the water supply lines. be prepared for water to spill.
6
Unthread the two screws on the top panel.
7
Slide and lift the panel off.
8
Unthread the four screws securing the rear cover.
9
Push the cover up and pull out to remove.
10
Disconnect the hose from the pressure sensor.
11
Unthread the three screws to release the sensor hose and bellow connector.
12
Now set the washer on its back.
13
Remove the tension clamp from the pump and remove the bellow.
14
Unthread the screw clamp and remove the bellow from the tub.
15
Remove the tension clamp as well as the hose retaining clip from the assembly.
16
To install the new drain bellow assembly, slide on the hose retaining clip and attach the tension clamp.
17
Slide the bellow over the pump and position the tension clamp to secure.
18
Install the bellow onto the tub and secure with the screw clamp.
19
Sit the washer upright.
20
Rethread the three screws to secure the sensor hose and bellow connector.
21
Run the sensor hose through the hose supports.
22
Connect the pressure sensor hose.
23
Slide the rear cover into position.
24
Rethread the four screws.
25
Set and slide the top panel onto the washer.
26
Rethread the two screws into the panel.
27
Rethread the water supply lines onto the hot and cold inlets.
28
Push the washer back into place.
29
Plug the power cord back in, and turn on the water supply, and your washer should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the drain bellow assembly in an LG washer (Model WM4000HBA). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
LG
Don't forget to like and comment on this video and subscribe to our channel!
This video provides step-by-step repair instructions for replacing the drain bellow assembly in an LG washer (Model WM4000HBA). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
LG
Don't forget to like and comment on this video and subscribe to our channel!
Step-By-Step Instructions
1
To replace the drain bellow assembly in your lg washer, you will need a short phillips screwdriver, channellock pliers, and a drill driver with a phillips bit.
2
Before you begin the procedure, unplug the washer.
3
Turn off the water supply.
4
Pull the washer away from the wall.
5
Unthread the water supply lines. be prepared for water to spill.
6
Unthread the two screws on the top panel.
7
Slide and lift the panel off.
8
Unthread the four screws securing the rear cover.
9
Push the cover up and pull out to remove.
10
Disconnect the hose from the pressure sensor.
11
Unthread the three screws to release the sensor hose and bellow connector.
12
Now set the washer on its back.
13
Remove the tension clamp from the pump and remove the bellow.
14
Unthread the screw clamp and remove the bellow from the tub.
15
Remove the tension clamp as well as the hose retaining clip from the assembly.
16
To install the new drain bellow assembly, slide on the hose retaining clip and attach the tension clamp.
17
Slide the bellow over the pump and position the tension clamp to secure.
18
Install the bellow onto the tub and secure with the screw clamp.
19
Sit the washer upright.
20
Rethread the three screws to secure the sensor hose and bellow connector.
21
Run the sensor hose through the hose supports.
22
Connect the pressure sensor hose.
23
Slide the rear cover into position.
24
Rethread the four screws.
25
Set and slide the top panel onto the washer.
26
Rethread the two screws into the panel.
27
Rethread the water supply lines onto the hot and cold inlets.
28
Push the washer back into place.
29
Plug the power cord back in, and turn on the water supply, and your washer should be ready for use.
Applicable Product Model
Parts Needed
Tub-to-Pump Hose
$101.53
Total$0.00
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com