Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairLG Washer Stator Wire Harness Replacement 6877ER1016S
This video provides step-by-step repair instructions for replacing the stator wire harness in an LG washer (Model WM4000HBA). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
LG
Don't forget to like and comment on this video and subscribe to our channel!
LG Washer Stator Wire Harness Replacement 6877ER1016S
Skill Level
Total Parts Cost
$50.07Estimated Savings
$112.5006:44
- Description
This video provides step-by-step repair instructions for replacing the stator wire harness in an LG washer (Model WM4000HBA). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
LG
Don't forget to like and comment on this video and subscribe to our channel!
Step By Step Instructions
1
To replace the stator wire harness in your lg washer, you will need an impact driver or ratchet, 17mm socket,10mm socket, channellock pliers, blue thread lock, and a drill driver with a phillips bit.
2
Before you begin the procedure, unplug the washer.
3
Turn off the water supply.
4
Pull the washer away from the wall.
5
Unthread the water supply lines. be prepared for water to spill.
6
Unthread the four screws securing the rear cover.
7
Push the cover upand pull out to remove.
8
Use the ratchet or impact driver to loosen and remove the mounting bolt and washer.
9
Pull the rotor off the tub shaft. this may be difficult.
10
Unthread the five screws securing the wire harness, bracket, and grounds.
11
Remove the three bolts securing the stator.
12
Pull the stator off of the tub and unplug the stator wire harness.
13
Remove the two blue retaining clips.
14
Remove the twist tie and uncover the plugs then detatch the plug from the main harness.
15
To install the new stator wire harness…
16
Connect the plug to the main harness then cover the wire with the plastic and attach the twist tie.
17
Snap in the two retaining clips.
18
Plug in the stator harness.
19
Position the stator on the tub, and secure it with the three bolts.
20
Rethread the five screws securing the grounds, bracket, and wire harness.
21
Align the rotor on the tub shaft.
22
Apply blue thread-locking fluid to the rotor bolt.
23
Insert the bolt and washer then tighten.
24
Slide the rear cover into position.
25
Rethread the four screws.
26
Rethread the water supply lines onto the hot and cold inlets.
27
Push the washer back into place.
28
Plug the power cord back in, and turn on the water supply, and your washer should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the stator wire harness in an LG washer (Model WM4000HBA). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
LG
Don't forget to like and comment on this video and subscribe to our channel!
This video provides step-by-step repair instructions for replacing the stator wire harness in an LG washer (Model WM4000HBA). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
LG
Don't forget to like and comment on this video and subscribe to our channel!
Step-By-Step Instructions
1
To replace the stator wire harness in your lg washer, you will need an impact driver or ratchet, 17mm socket,10mm socket, channellock pliers, blue thread lock, and a drill driver with a phillips bit.
2
Before you begin the procedure, unplug the washer.
3
Turn off the water supply.
4
Pull the washer away from the wall.
5
Unthread the water supply lines. be prepared for water to spill.
6
Unthread the four screws securing the rear cover.
7
Push the cover upand pull out to remove.
8
Use the ratchet or impact driver to loosen and remove the mounting bolt and washer.
9
Pull the rotor off the tub shaft. this may be difficult.
10
Unthread the five screws securing the wire harness, bracket, and grounds.
11
Remove the three bolts securing the stator.
12
Pull the stator off of the tub and unplug the stator wire harness.
13
Remove the two blue retaining clips.
14
Remove the twist tie and uncover the plugs then detatch the plug from the main harness.
15
To install the new stator wire harness…
16
Connect the plug to the main harness then cover the wire with the plastic and attach the twist tie.
17
Snap in the two retaining clips.
18
Plug in the stator harness.
19
Position the stator on the tub, and secure it with the three bolts.
20
Rethread the five screws securing the grounds, bracket, and wire harness.
21
Align the rotor on the tub shaft.
22
Apply blue thread-locking fluid to the rotor bolt.
23
Insert the bolt and washer then tighten.
24
Slide the rear cover into position.
25
Rethread the four screws.
26
Rethread the water supply lines onto the hot and cold inlets.
27
Push the washer back into place.
28
Plug the power cord back in, and turn on the water supply, and your washer should be ready for use.
Applicable Product Model
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com