Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairLG Washer Motor Stator Replacement AJB73816004
This video provides step-by-step repair instructions for replacing the motor stator in an LG washer (Model WM4000HBA). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
LG
Don't forget to like and comment on this video and subscribe to our channel!
LG Washer Motor Stator Replacement AJB73816004
Skill Level
Total Parts Cost
$347.27Estimated Savings
$112.5004:55
- Description
This video provides step-by-step repair instructions for replacing the motor stator in an LG washer (Model WM4000HBA). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
LG
Don't forget to like and comment on this video and subscribe to our channel!
Step By Step Instructions
1
To replace the motor stator in your lg washer, you will need an impact driver or ratchet, channellock pliers, 17mm socket,10mm socket, blue thread lock, and a drill driver with a phillips bit.
2
Before you begin the procedure, unplug the washer.
3
Turn off the water supply.
4
Pull the washer away from the wall.
5
Unthread the water supply lines. be prepared for water to spill.
6
Unthread the four screws securing the rear cover.
7
Push the cover up and pull out to remove.
8
Use the ratchet or impact driver to loosen and remove the mounting bolt and washer.
9
Pull the rotor off the tub shaft. this may be difficult.
10
Unthread the screw securing the stator wire bracket.
11
Remove the three bolts securing the stator and pull the stator off of the tub.
12
Unplug the wire harness.
13
To install the new motor stator, plug in the harness.
14
Position the stator on the tub, and secure it with the three bolts.
15
Secure the wire bracket with the screw.
16
Align the rotor on the tub shaft.
17
Apply blue thread-locking fluid to the rotor bolt.
18
Insert the bolt and washer then tighten.
19
Slide the rear cover into position.
20
Rethread the four screws.
21
Rethread the water supply lines.
22
Push the washer back into place.
23
Plug the power cord back in, and turn on the water supply, and your washer should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the motor stator in an LG washer (Model WM4000HBA). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
LG
Don't forget to like and comment on this video and subscribe to our channel!
This video provides step-by-step repair instructions for replacing the motor stator in an LG washer (Model WM4000HBA). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
LG
Don't forget to like and comment on this video and subscribe to our channel!
Step-By-Step Instructions
1
To replace the motor stator in your lg washer, you will need an impact driver or ratchet, channellock pliers, 17mm socket,10mm socket, blue thread lock, and a drill driver with a phillips bit.
2
Before you begin the procedure, unplug the washer.
3
Turn off the water supply.
4
Pull the washer away from the wall.
5
Unthread the water supply lines. be prepared for water to spill.
6
Unthread the four screws securing the rear cover.
7
Push the cover up and pull out to remove.
8
Use the ratchet or impact driver to loosen and remove the mounting bolt and washer.
9
Pull the rotor off the tub shaft. this may be difficult.
10
Unthread the screw securing the stator wire bracket.
11
Remove the three bolts securing the stator and pull the stator off of the tub.
12
Unplug the wire harness.
13
To install the new motor stator, plug in the harness.
14
Position the stator on the tub, and secure it with the three bolts.
15
Secure the wire bracket with the screw.
16
Align the rotor on the tub shaft.
17
Apply blue thread-locking fluid to the rotor bolt.
18
Insert the bolt and washer then tighten.
19
Slide the rear cover into position.
20
Rethread the four screws.
21
Rethread the water supply lines.
22
Push the washer back into place.
23
Plug the power cord back in, and turn on the water supply, and your washer should be ready for use.
Applicable Product Model
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com