Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairLG Washer Control Board Assembly Replacement EBR89581110
This video provides step-by-step repair instructions for replacing the control board assembly in an LG washer (Model WM4000HBA). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
LG
Don't forget to like and comment on this video and subscribe to our channel!
LG Washer Control Board Assembly Replacement EBR89581110
Skill Level
Total Parts Cost
$395.51Estimated Savings
$112.5015:32
- Description
This video provides step-by-step repair instructions for replacing the control board assembly in an LG washer (Model WM4000HBA). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
LG
Don't forget to like and comment on this video and subscribe to our channel!
Step By Step Instructions
1
To replace the control board assembly in your lg washer, you will need needle nose pliers, pliers, zip ties, wire cutters, a spring removal tool, and a drill driver with a phillips bit.
2
Before you begin the procedure, unplug the washer.
3
Pull the washer away from the wall.
4
Unthread the two screws on the top panel.
5
Slide and lift the top panel off.
6
Unthread the screw securing the right side of the control panel.
7
Open the drawer and push down on the “push” tab and remove the detergent assembly.
8
Unthread the two screws that secure the left side of the control panel.
9
Pry the three tabs then pull back and lift up to free the control panel.
10
Unplug the harness to the control panel.
11
Open the drain clean-out door.
12
Unclip the drain hose then unthread the two phillips screws.
13
Pull out the case.
14
Unthread the screw under the drain pump clean-out.
15
Use the spring removal tool or needle nose pliers to remove the retaining ring.
16
Detach the boot seal from the front panel.
17
Unthread the six screws on the front panel.
18
Push the panel down to release it from the tab.
19
Unplug the door lock from the harness.
20
Lift the front panel up and away from the washer.
21
Unthread the four screws securing the rear cover.
22
Push the cover up and pull out to remove.
23
Unthread the ground screw for the predominantly green wire with a yellow stripe.
24
Noting the orientation of the wires, unplug the pressure sensor.
25
Unplug the inlet valves.
26
Remove the pink plug from the noise filter.
27
Unplug the temperature sensor.
28
Now, remove the blue retaining clip and free it from the frame.
29
Remove the white and blue retaining clips on the back of the washer and free them from the frame.
30
Remove the twist tie and uncover the blue harness and unplug it.
31
On the front of the washer, remove the three plugs on the heating element.
32
Cut the three zip ties securing the harness.
33
Pull back the plastic cover and unplug the harness.
34
Remove the blue wire retaining clip.
35
Push in the tab on the wire guide rail then push up to unseat and remove the rail from the frame.
36
Pull the wires through the frame and rest them on the tub.
37
Remove the orange retaining clip above the noise filter.
38
Unthread the screw securing the control board assembly.
39
Pull back the tab then slide and lift out the assembly.
40
To install the new control board assembly, place the tabs in the panel and press down to secure it, then slide forward to lock and seat the peg in the frame.
41
Rethread the screw to the control board.
42
Snap in the orange retaining clip above the noise filter.
43
Run the respective wires down the front and backside in the frame.
44
Insert and seat the wire guide rail into the frame.
45
Snap in the blue retaining clip on the front side of the frame.
46
Connect the three plugs to the heating element.
47
Secure them with the zip tie.
48
Plug in the drain pump, then cover it with the plastic and secure it with the zip tie.
49
Run the wires through the wire guides.
50
Secure the wires with the zip tie.
51
On the back of washer, connect the plug to the stator harness,then cover it with the plastic and secure it with the twist tie.
52
Snap in the five retaining clips.
53
Plug in the temperature sensor.
54
Run the control panel wire through the frame and snap in the retaining clip.
55
Plug in the pink harness into the noise filter.
56
Plug in the inlet valves.
57
Plug in the pressure sensor.
58
Rethread the ground wire to the frame.
59
Set the panel on the three tabs and plug in the door lock.
60
Push the panel upright and lock it in place with the tab.
61
Rethread the six screws into the panel.
62
Rethread the screw underneath the drain pump clean-out.
63
Feed the drain hose through the case and place in the washer.
64
Rethread the two phillips screws and clip in the drain hose.
65
Tuck the boot seal into the front panel.
66
Tuck the ring into the boot starting at the top.
67
Use the spring removal tool or needle nose pliers to insert the ring and securely seat it into the seal.
68
Plug the wire harness back into the display board.
69
Insert the control panel into its grooves and push forward to snap in place, rethread the two screws on the left side of the control panel.
70
Align the detergent assembly and push in until it snaps into place.
71
Rethread the screw on the right side of the control panel.
72
Slide the rear cover into position.
73
Rethread the four screws.
74
Set and slide the top panel onto the washer.
75
Rethread the water supply lines over the hot and cold inlets.
76
Rethread the two screws into the panel.
77
Push the washer back into place.
78
Plug the power cord back in, and your washer should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the control board assembly in an LG washer (Model WM4000HBA). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
LG
Don't forget to like and comment on this video and subscribe to our channel!
This video provides step-by-step repair instructions for replacing the control board assembly in an LG washer (Model WM4000HBA). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
LG
Don't forget to like and comment on this video and subscribe to our channel!
Step-By-Step Instructions
1
To replace the control board assembly in your lg washer, you will need needle nose pliers, pliers, zip ties, wire cutters, a spring removal tool, and a drill driver with a phillips bit.
2
Before you begin the procedure, unplug the washer.
3
Pull the washer away from the wall.
4
Unthread the two screws on the top panel.
5
Slide and lift the top panel off.
6
Unthread the screw securing the right side of the control panel.
7
Open the drawer and push down on the “push” tab and remove the detergent assembly.
8
Unthread the two screws that secure the left side of the control panel.
9
Pry the three tabs then pull back and lift up to free the control panel.
10
Unplug the harness to the control panel.
11
Open the drain clean-out door.
12
Unclip the drain hose then unthread the two phillips screws.
13
Pull out the case.
14
Unthread the screw under the drain pump clean-out.
15
Use the spring removal tool or needle nose pliers to remove the retaining ring.
16
Detach the boot seal from the front panel.
17
Unthread the six screws on the front panel.
18
Push the panel down to release it from the tab.
19
Unplug the door lock from the harness.
20
Lift the front panel up and away from the washer.
21
Unthread the four screws securing the rear cover.
22
Push the cover up and pull out to remove.
23
Unthread the ground screw for the predominantly green wire with a yellow stripe.
24
Noting the orientation of the wires, unplug the pressure sensor.
25
Unplug the inlet valves.
26
Remove the pink plug from the noise filter.
27
Unplug the temperature sensor.
28
Now, remove the blue retaining clip and free it from the frame.
29
Remove the white and blue retaining clips on the back of the washer and free them from the frame.
30
Remove the twist tie and uncover the blue harness and unplug it.
31
On the front of the washer, remove the three plugs on the heating element.
32
Cut the three zip ties securing the harness.
33
Pull back the plastic cover and unplug the harness.
34
Remove the blue wire retaining clip.
35
Push in the tab on the wire guide rail then push up to unseat and remove the rail from the frame.
36
Pull the wires through the frame and rest them on the tub.
37
Remove the orange retaining clip above the noise filter.
38
Unthread the screw securing the control board assembly.
39
Pull back the tab then slide and lift out the assembly.
40
To install the new control board assembly, place the tabs in the panel and press down to secure it, then slide forward to lock and seat the peg in the frame.
41
Rethread the screw to the control board.
42
Snap in the orange retaining clip above the noise filter.
43
Run the respective wires down the front and backside in the frame.
44
Insert and seat the wire guide rail into the frame.
45
Snap in the blue retaining clip on the front side of the frame.
46
Connect the three plugs to the heating element.
47
Secure them with the zip tie.
48
Plug in the drain pump, then cover it with the plastic and secure it with the zip tie.
49
Run the wires through the wire guides.
50
Secure the wires with the zip tie.
51
On the back of washer, connect the plug to the stator harness,then cover it with the plastic and secure it with the twist tie.
52
Snap in the five retaining clips.
53
Plug in the temperature sensor.
54
Run the control panel wire through the frame and snap in the retaining clip.
55
Plug in the pink harness into the noise filter.
56
Plug in the inlet valves.
57
Plug in the pressure sensor.
58
Rethread the ground wire to the frame.
59
Set the panel on the three tabs and plug in the door lock.
60
Push the panel upright and lock it in place with the tab.
61
Rethread the six screws into the panel.
62
Rethread the screw underneath the drain pump clean-out.
63
Feed the drain hose through the case and place in the washer.
64
Rethread the two phillips screws and clip in the drain hose.
65
Tuck the boot seal into the front panel.
66
Tuck the ring into the boot starting at the top.
67
Use the spring removal tool or needle nose pliers to insert the ring and securely seat it into the seal.
68
Plug the wire harness back into the display board.
69
Insert the control panel into its grooves and push forward to snap in place, rethread the two screws on the left side of the control panel.
70
Align the detergent assembly and push in until it snaps into place.
71
Rethread the screw on the right side of the control panel.
72
Slide the rear cover into position.
73
Rethread the four screws.
74
Set and slide the top panel onto the washer.
75
Rethread the water supply lines over the hot and cold inlets.
76
Rethread the two screws into the panel.
77
Push the washer back into place.
78
Plug the power cord back in, and your washer should be ready for use.
Applicable Product Model
Parts Needed
Power Supply Board
$395.51
Total$0.00
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com