Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairLG Washer Out-of-Balance Sensor Replacement EBD48922806
This video provides step-by-step repair instructions for replacing the Out-of-Balance Sensor in an LG washer (Model WM4000HBA). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
LG
Don't forget to like and comment on this video and subscribe to our channel!
LG Washer Out-of-Balance Sensor Replacement EBD48922806
Skill Level
Total Parts Cost
$107.89Estimated Savings
$112.5004:14
- Description
This video provides step-by-step repair instructions for replacing the Out-of-Balance Sensor in an LG washer (Model WM4000HBA). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
LG
Don't forget to like and comment on this video and subscribe to our channel!
Step By Step Instructions
1
To replace the temperature sensor in your lg washer, you will need needlenose pliers and a drill driver with a phillips bit.
2
Before you begin the procedure, unplug the washer.
3
Pull the washer away from the wall.
4
Unthread the two screws on the top panel.
5
Slide and lift the panel off.
6
Unthread the screw securing the right side of the control panel.
7
Open the drawer and push down on the “push” tab and remove the detergent assembly.
8
Unthread the two screws that secure the left side of the control panel.
9
Pry the three tabs then pull back and lift up to free the control panel.
10
Pinch the retaining clip and free it from the frame.
11
Insert the control panel into its grooves and push forward to snap in place, rethread the two screws on the left side of the control panel.
12
Align the detergent assembly and push in until it snaps into place.
13
Rethread the screw on the right side of the control panel.
14
Unthread the two screws that secure the sensor. hold onto the metal plate for reinstallation.
15
Unplug the sensor.
16
To install the new temperature sensor, place the sensor in the drum then bend the wire 180 degrees, set the metal plate and rethread the screw to secure it.
17
Rethread the screw to the retaining clip.
18
Plug in the sensor.
19
Snap in the retaining clip.
20
Set and slide the panel onto the washer.
21
Rethread the two screws into the panel.
22
Push the washer back into place.
23
Plug the power cord back in, and your washer should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the Out-of-Balance Sensor in an LG washer (Model WM4000HBA). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
LG
Don't forget to like and comment on this video and subscribe to our channel!
This video provides step-by-step repair instructions for replacing the Out-of-Balance Sensor in an LG washer (Model WM4000HBA). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
LG
Don't forget to like and comment on this video and subscribe to our channel!
Step-By-Step Instructions
1
To replace the temperature sensor in your lg washer, you will need needlenose pliers and a drill driver with a phillips bit.
2
Before you begin the procedure, unplug the washer.
3
Pull the washer away from the wall.
4
Unthread the two screws on the top panel.
5
Slide and lift the panel off.
6
Unthread the screw securing the right side of the control panel.
7
Open the drawer and push down on the “push” tab and remove the detergent assembly.
8
Unthread the two screws that secure the left side of the control panel.
9
Pry the three tabs then pull back and lift up to free the control panel.
10
Pinch the retaining clip and free it from the frame.
11
Insert the control panel into its grooves and push forward to snap in place, rethread the two screws on the left side of the control panel.
12
Align the detergent assembly and push in until it snaps into place.
13
Rethread the screw on the right side of the control panel.
14
Unthread the two screws that secure the sensor. hold onto the metal plate for reinstallation.
15
Unplug the sensor.
16
To install the new temperature sensor, place the sensor in the drum then bend the wire 180 degrees, set the metal plate and rethread the screw to secure it.
17
Rethread the screw to the retaining clip.
18
Plug in the sensor.
19
Snap in the retaining clip.
20
Set and slide the panel onto the washer.
21
Rethread the two screws into the panel.
22
Push the washer back into place.
23
Plug the power cord back in, and your washer should be ready for use.
Applicable Product Model
Parts Needed
Out-of-Balance Sensor
$107.89
Total$0.00
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com