Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairGE Washer Internal Drain Hose Assembly Replacement WH41X24177
This video provides step-by-step repair instructions for replacing the internal drain hose assembly in a GE washer (Model GTW465ASN2WW). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
GE
Screws affiliated with washer-
Don't forget to like and comment on this video and subscribe to our channel!
GE Washer Internal Drain Hose Assembly Replacement WH41X24177
Skill Level
Total Parts Cost
$18.89Estimated Savings
$112.5003:39
- Description
This video provides step-by-step repair instructions for replacing the internal drain hose assembly in a GE washer (Model GTW465ASN2WW). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
GE
Screws affiliated with washer-
Don't forget to like and comment on this video and subscribe to our channel!
Step By Step Instructions
1
To replace the internal drain hose assembly on your ge washer, you will need pliers and a drill driver with a 1/4” bit.
2
Before you begin the procedure, shut off the water supply
3
Unplug the power to the appliance.
4
Remove the drain line from the wall
5
Remove the hot and cold-water supply lines from the inlet valves.
6
Set a drain pan or towel underneath the hose.
7
Pinch the clamp and pull the hose from the washer.
8
Unthread the screw on the plate closest to the drain opening.
9
Press the plastic tab and slide the drain outlet up and push in
10
Tip the washer back and prop it up using a wooden block or chair.
11
Slide down the clamp securing the hose to the drain pump.
12
Slide the hose off of the drain pump and remove the assembly from the appliance.
13
Remove the clamp.
14
To install the new internal drain hose assembly.
15
Slide the clamp over the hose.
16
Connect the hose to the drain pump, then slide the clamp to secure it.
17
Line the drain pump outlet up to the metal plate then slide it in and up to snap in place.
18
Set the washer upright.
19
Rethread the screw.
20
While pinching the clamp, slide the hose over the outlet and release it.
21
Insert the drain hose back into the wall drain.
22
Reattatch the hot and cold-water supply lines.
23
Turn on the water supply
24
Plug in the power.
25
And your washer should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the internal drain hose assembly in a GE washer (Model GTW465ASN2WW). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
GE
Screws affiliated with washer-
Don't forget to like and comment on this video and subscribe to our channel!
This video provides step-by-step repair instructions for replacing the internal drain hose assembly in a GE washer (Model GTW465ASN2WW). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
GE
Screws affiliated with washer-
Don't forget to like and comment on this video and subscribe to our channel!
Step-By-Step Instructions
1
To replace the internal drain hose assembly on your ge washer, you will need pliers and a drill driver with a 1/4” bit.
2
Before you begin the procedure, shut off the water supply
3
Unplug the power to the appliance.
4
Remove the drain line from the wall
5
Remove the hot and cold-water supply lines from the inlet valves.
6
Set a drain pan or towel underneath the hose.
7
Pinch the clamp and pull the hose from the washer.
8
Unthread the screw on the plate closest to the drain opening.
9
Press the plastic tab and slide the drain outlet up and push in
10
Tip the washer back and prop it up using a wooden block or chair.
11
Slide down the clamp securing the hose to the drain pump.
12
Slide the hose off of the drain pump and remove the assembly from the appliance.
13
Remove the clamp.
14
To install the new internal drain hose assembly.
15
Slide the clamp over the hose.
16
Connect the hose to the drain pump, then slide the clamp to secure it.
17
Line the drain pump outlet up to the metal plate then slide it in and up to snap in place.
18
Set the washer upright.
19
Rethread the screw.
20
While pinching the clamp, slide the hose over the outlet and release it.
21
Insert the drain hose back into the wall drain.
22
Reattatch the hot and cold-water supply lines.
23
Turn on the water supply
24
Plug in the power.
25
And your washer should be ready for use.
Applicable Product Model
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com