Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairGE Washer Transmission Pulley & Nut Replacement WH03X32097
This video provides step-by-step repair instructions for replacing the transmission pulley & nut in a GE washer (Model GTW465ASN2WW). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
GE
Screws affiliated with washer-
Don't forget to like and comment on this video and subscribe to our channel!
GE Washer Transmission Pulley & Nut Replacement WH03X32097
Skill Level
Total Parts Cost
$32.14Estimated Savings
$112.5004:23
- Description
This video provides step-by-step repair instructions for replacing the transmission pulley & nut in a GE washer (Model GTW465ASN2WW). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
GE
Screws affiliated with washer-
Don't forget to like and comment on this video and subscribe to our channel!
Step By Step Instructions
1
To replace the transmission pulley & nut in your ge washer, you will need an impact driver with a 1/4” bit, pliers, a 3/8” socket, a 14mm socket, a pulley remover, and a 1/4” socket adapter.
2
Before you begin the procedure, unplug the power to the washer.
3
Shut off the water supply
4
Remove the drain line from the wall
5
Remove the hot and cold-water supply lines from the inlet valve.
6
Prop up the washer. you can use a wooden block or chair.
7
Unthread the three screws on the protective belt cover to remove it.
8
Pull the belt off of the big pulley first then remove it.
9
Using the 14mm socket, unthread the nut.
10
Attach the pulley remover to the pulley and tighten down until the pulley comes off.
11
To install the new transmission pulley & nut, slide the pulley on the shaft and line it up with the splines, then thread the nut onto the shaft. while tightening, the pulley will seat into position.
12
Place the belt ribside facing inward over the big pulley then stretch the belt over the small pulley.
13
Rotate the pulleys to align the belt properly.
14
Align the cover and start one of the three screws.
15
Place the grounding connector over the screw and rethread it to the bottom of the transmission.
16
Now rethread the last screw.
17
Prop up the washer.
18
Reattatch the hot and cold-water supply lines.
19
Insert the drain hose back into the wall drain.
20
Turn on the water supply
21
Plug in the power.
Description
This video provides step-by-step repair instructions for replacing the transmission pulley & nut in a GE washer (Model GTW465ASN2WW). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
GE
Screws affiliated with washer-
Don't forget to like and comment on this video and subscribe to our channel!
This video provides step-by-step repair instructions for replacing the transmission pulley & nut in a GE washer (Model GTW465ASN2WW). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
GE
Screws affiliated with washer-
Don't forget to like and comment on this video and subscribe to our channel!
Step-By-Step Instructions
1
To replace the transmission pulley & nut in your ge washer, you will need an impact driver with a 1/4” bit, pliers, a 3/8” socket, a 14mm socket, a pulley remover, and a 1/4” socket adapter.
2
Before you begin the procedure, unplug the power to the washer.
3
Shut off the water supply
4
Remove the drain line from the wall
5
Remove the hot and cold-water supply lines from the inlet valve.
6
Prop up the washer. you can use a wooden block or chair.
7
Unthread the three screws on the protective belt cover to remove it.
8
Pull the belt off of the big pulley first then remove it.
9
Using the 14mm socket, unthread the nut.
10
Attach the pulley remover to the pulley and tighten down until the pulley comes off.
11
To install the new transmission pulley & nut, slide the pulley on the shaft and line it up with the splines, then thread the nut onto the shaft. while tightening, the pulley will seat into position.
12
Place the belt ribside facing inward over the big pulley then stretch the belt over the small pulley.
13
Rotate the pulleys to align the belt properly.
14
Align the cover and start one of the three screws.
15
Place the grounding connector over the screw and rethread it to the bottom of the transmission.
16
Now rethread the last screw.
17
Prop up the washer.
18
Reattatch the hot and cold-water supply lines.
19
Insert the drain hose back into the wall drain.
20
Turn on the water supply
21
Plug in the power.
Applicable Product Model
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com