Kenmore Washing Machine Parts

Kenmore Washing Machine Parts

Kenmore washers are built by Whirlpool, LG, and Frigidaire depending on your model series — and that matters when you're ordering parts. The model number prefix tells you the OEM: 110.xxxxx models are Whirlpool-built (prone to lid switch and drain pump failures), while other prefixes point to different manufacturers entirely. Once you confirm your builder, we stock the exact OEM parts your machine needs.

Whether your Kenmore is a top-load or front-load, the same high-failure parts show up across the brand: lid switches that jam the whole cycle, drain pumps that leave standing water, water inlet valves that slow-fill or stop cold, and control boards that throw error codes. We carry genuine OEM parts for all Kenmore model series — not aftermarket substitutes that won't fit or seal correctly.

• Lid switch won't let the washer start or complete a cycle: Lid switches are the safety interlock; one bad switch stops everything
• Drain pump fails and water sits in the tub: Standing water means the pump's seized or the motor's burned out
• Water inlet valve won't fill, fills too slowly, or only one temperature works: Dual solenoid valves control hot and cold independently
• Control board shows error codes or goes silent mid-cycle: OEM board replacement is a primary reliable fix for electronic faults
• Tub bearing rumbles loudly during spin, especially on Whirlpool-built models: Tub bearings wear out; LG and Frigidaire Kenmore models use different bearing assemblies

Find your exact model number: it's on a sticker inside the washer door or behind the control panel — and we'll match you with the correct OEM Kenmore parts. Whirlpool, LG, and Frigidaire all have different part platforms, so model-number lookup is essential.

Kenmore Washing Machine Parts — FAQ

Why does my Kenmore model number matter so much for parts?

Kenmore is a Sears house brand built by three different manufacturers — Whirlpool, LG, and Frigidaire. The model prefix tells you who built it: 110.xxxxx = Whirlpool, 253.xxxxx = Frigidaire refrigerator (not washer), 795.xxxxx = LG. Each OEM uses completely different parts for the lid switch, control board, pump, and bearing assemblies. Ordering the wrong parts wastes money and time. Use your full model number — it's on the sticker inside the door or behind the control panel — and we'll show you the correct OEM parts.

My Kenmore washer won't drain — is it always the pump?

Standing water almost always points to the drain pump, but not always because the pump is broken. First, check if the drain hose is kinked or clogged — that's the fastest, cheapest fix. If the hose is clear and water still won't drain, the pump motor has likely failed or the impeller is jammed. If your Whirlpool-built Kenmore (110.xxxxx model) also shows error codes, the control board may be preventing pump activation. We carry OEM drain pump assemblies for all Kenmore builders, plus the inlet valve and control board if those are the real culprit.

What's the difference between Kenmore Elite and regular Kenmore parts?

Kenmore Elite models use factory-certified parts — better control boards, heavier-duty pumps, upgraded suspension systems — but the parts are still OEM-specific to whichever manufacturer built that machine. Elite status doesn't change the fact that you need the exact model number to get the right parts. What it does mean is that Elite machines are often worth repairing; regular Kenmore machines at the entry level sometimes hit a break-even point where replacement makes more sense. Always look up your full model number — Elite or not — before ordering.

My Kenmore lid switch is jammed — can I just bypass it?

The lid switch is a safety device; bypassing it defeats the lock that prevents the lid from opening during a spin cycle. Don't bypass it. A new OEM lid switch is a $15 to $40 part and takes 10 minutes to replace. If the switch itself isn't broken but the latch is bent or the switch is just stuck with detergent buildup, clean around the mechanism first. If the washer still won't recognize a closed lid, replace the switch with the OEM part for your model.

Order Kenmore Washing Machine Parts Online

Ordering Kenmore washing machine parts online is simple and helps you find genuine OEM parts for your unit. With same-day shipping on most in-stock items, you'll have your replacement part fast, minimizing downtime. Our model/part number lookup finds the exact OEM part for your unit, and every order is backed by our 365-day return policy and price-match guarantee. Browse our repair help section for troubleshooting tips, part testing guides, and step-by-step installation videos for your specific product.

Kenmore Washing Machine Model Number: Where to Look

Kenmore prints the model number on a label inside the washer's door frame or behind the control panel, though some top-load machines place it under the lid or on the back panel. Look for a tag showing the complete model number, including its prefix and suffix, rather than a serial number or part number. Punch it into the search bar to sort the catalog down to your model's parts. That filters the full Kenmore washing machine selection, so every associated part is matched to your specific unit. You can order with confidence knowing the fit is right.