Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairWhirlpool 27" Gas Dryer Moisture Sensor Bar #3387223
Whirlpool 27" Gas Dryer Moisture Sensor Bar #3387223
Skill Level
Total Parts Cost
$11.06Estimated Savings
$112.5003:31
- Description
This video provides step-by-step instructions for replacing the moisture sensor bar on 27” Whirlpool gas dryers. The most common reasons for replacing the moisture sensor bar are when the dryer takes too long or won’t stop.
All of the information in this moisture sensor bar replacement video is applicable to the following brands: Kenmore, Whirlpool, KitchenAid, Maytag, Amana, Inglis
Tools used: hex socket, flat-head screwdriver, Phillips head screwdriver, putty knife, pliers
All of the information in this moisture sensor bar replacement video is applicable to the following brands: Kenmore, Whirlpool, KitchenAid, Maytag, Amana, Inglis
Tools used: hex socket, flat-head screwdriver, Phillips head screwdriver, putty knife, pliers
Step By Step Instructions
1
As with any repair, be sure you unplug the appliance before beginning.
2
Your first step is to detach the control panel.
3
Depending on your model, you will either insert a putty knife under the panel to release the two clips or you will pull off both plastic end caps and remove the screws found underneath.
4
Now, rotate the control panel up.
5
Remove the screws securing the main top and slide the top off.
6
Next, insert a flathead screwdriver between the upper and lower front panels to release the two clips and detach the lower panel.
7
Remove the upper panel mounting screws along with the lint screen duct screw and, if applicable, the screw securing the grounding wire.
8
Detach the moisture sensor wire and the two door springs.
9
Now, disconnect the door switch wire connector remove the screws from the top of the upper panel and lift the upper panel off.
10
Pull the lint screen out and remove the mounting screws to release the outlet screen grille.
11
Using needle-nose pliers, squeeze the tab to release the old moisture sensor bar.
12
Install the new moisture sensor bar by snapping it into the grille.
13
Position the grille and secure it with the mounting screws.
14
Replace the lint screen.
15
Reinstall the upper front panel by aligning the two rollers on the drum rim and positioning the top lip of the panel on the cabinet brackets.
16
Replace all four panel screws along with the lint screen duct screw and, if applicable, the screw securing the grounding wire.
17
Reattach the moisture sensor wire and the door springs.
18
Now, replace the lower front panel by snapping it into position.
19
Reconnect the door switch wire connector at the top of the dryer.
20
Slide the main top on and secure it with the screws.
21
Rotate the control panel down and lock it into place.
22
If applicable, replace the screws and end caps.
23
You’re now ready to plug the appliance back in to make sure it’s functioning properly.
Description
This video provides step-by-step instructions for replacing the moisture sensor bar on 27” Whirlpool gas dryers. The most common reasons for replacing the moisture sensor bar are when the dryer takes too long or won’t stop.
All of the information in this moisture sensor bar replacement video is applicable to the following brands: Kenmore, Whirlpool, KitchenAid, Maytag, Amana, Inglis
Tools used: hex socket, flat-head screwdriver, Phillips head screwdriver, putty knife, pliers
All of the information in this moisture sensor bar replacement video is applicable to the following brands: Kenmore, Whirlpool, KitchenAid, Maytag, Amana, Inglis
Tools used: hex socket, flat-head screwdriver, Phillips head screwdriver, putty knife, pliers
Step-By-Step Instructions
1
As with any repair, be sure you unplug the appliance before beginning.
2
Your first step is to detach the control panel.
3
Depending on your model, you will either insert a putty knife under the panel to release the two clips or you will pull off both plastic end caps and remove the screws found underneath.
4
Now, rotate the control panel up.
5
Remove the screws securing the main top and slide the top off.
6
Next, insert a flathead screwdriver between the upper and lower front panels to release the two clips and detach the lower panel.
7
Remove the upper panel mounting screws along with the lint screen duct screw and, if applicable, the screw securing the grounding wire.
8
Detach the moisture sensor wire and the two door springs.
9
Now, disconnect the door switch wire connector remove the screws from the top of the upper panel and lift the upper panel off.
10
Pull the lint screen out and remove the mounting screws to release the outlet screen grille.
11
Using needle-nose pliers, squeeze the tab to release the old moisture sensor bar.
12
Install the new moisture sensor bar by snapping it into the grille.
13
Position the grille and secure it with the mounting screws.
14
Replace the lint screen.
15
Reinstall the upper front panel by aligning the two rollers on the drum rim and positioning the top lip of the panel on the cabinet brackets.
16
Replace all four panel screws along with the lint screen duct screw and, if applicable, the screw securing the grounding wire.
17
Reattach the moisture sensor wire and the door springs.
18
Now, replace the lower front panel by snapping it into position.
19
Reconnect the door switch wire connector at the top of the dryer.
20
Slide the main top on and secure it with the screws.
21
Rotate the control panel down and lock it into place.
22
If applicable, replace the screws and end caps.
23
You’re now ready to plug the appliance back in to make sure it’s functioning properly.
Applicable Product Model
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com