Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairWhirlpool/Kenmore Gas Dryer Signal Switch Replacement #3405151
Whirlpool/Kenmore Gas Dryer Signal Switch Replacement #3405151
Skill Level
Total Parts Cost
$103.14Estimated Savings
$112.5001:36
- Description
This video provides step-by-step instructions for replacing the signal switch on Whirlpool gas dryers. The most common reason for replacing the signal switch is that the dryer does not buzz at the end of its cycle but everything else works.
All of the information in this signal switch replacement video is applicable to the following brands: Kenmore, Whirlpool, Maytag
Tools used: hex socket, putty knife
All of the information in this signal switch replacement video is applicable to the following brands: Kenmore, Whirlpool, Maytag
Tools used: hex socket, putty knife
Step By Step Instructions
1
As with any repair, be sure you unplug the appliance before beginning.
2
Your first step is to remove the signal switch knob. This may require some effort - You can use string or wire to help pry it off.
3
Next, detach the control panel.
4
Depending on your model, you will either insert a putty knife under the panel to release the two clips or you will pull off both plastic end caps and remove the screws found underneath.
5
Now, rotate the control panel up.
6
Pull the tab and rotate the old switch to remove.
7
Squeeze the tabs to release the wire connector.
8
You’re now ready to install the new signal switch.
9
Reattach the wire connector then insert the switch into the control panel and rotate until it snaps into position.
10
Rotate the control panel back down, and snap it into place.
11
If applicable, replace the screws and end caps.
12
Reinstall the signal switch knob and plug the appliance back in to make sure it’s functioning properly.
Description
This video provides step-by-step instructions for replacing the signal switch on Whirlpool gas dryers. The most common reason for replacing the signal switch is that the dryer does not buzz at the end of its cycle but everything else works.
All of the information in this signal switch replacement video is applicable to the following brands: Kenmore, Whirlpool, Maytag
Tools used: hex socket, putty knife
All of the information in this signal switch replacement video is applicable to the following brands: Kenmore, Whirlpool, Maytag
Tools used: hex socket, putty knife
Step-By-Step Instructions
1
As with any repair, be sure you unplug the appliance before beginning.
2
Your first step is to remove the signal switch knob. This may require some effort - You can use string or wire to help pry it off.
3
Next, detach the control panel.
4
Depending on your model, you will either insert a putty knife under the panel to release the two clips or you will pull off both plastic end caps and remove the screws found underneath.
5
Now, rotate the control panel up.
6
Pull the tab and rotate the old switch to remove.
7
Squeeze the tabs to release the wire connector.
8
You’re now ready to install the new signal switch.
9
Reattach the wire connector then insert the switch into the control panel and rotate until it snaps into position.
10
Rotate the control panel back down, and snap it into place.
11
If applicable, replace the screws and end caps.
12
Reinstall the signal switch knob and plug the appliance back in to make sure it’s functioning properly.
Applicable Product Model
Parts Needed
Buzzer Switch
$103.14
Total$0.00
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com