Video & Articles: Appliance & Equipment RepairWhirlpool/Kenmore Gas Dryer Wrinkle Shield Switch #3405152

Whirlpool/Kenmore Gas Dryer Wrinkle Shield Switch #3405152

01:34
This video provides step-by-step repair instructions for replacing the wrinkle shield rotary switch on a Whirlpool/Kenmore gas dryer. The most common reason for replacing the wrinkle shield switch is when clothes are coming out wrinkled.

All of the information for this wrinkle shield rotary switch replacement video is applicable to the following brands:
Whirlpool, Kenmore, Maytag, Amana, Crosley, Estate

Tools needed: hex socket, putty knife

Step By Step Instructions

1
As with any repair, be sure you unplug the appliance before beginning.
2
Your first step is to remove the wrinkle guard knob. This may require some effort - You can use string or wire to help pry it off.
3
Next, detach the control panel.
4
Depending on your model, you will either insert a putty knife under the panel to release the two clips or you will pull off both plastic end caps and remove the screws found underneath.
5
Now, rotate the control panel up.
6
Pull the tab and rotate the old switch to remove.
7
Squeeze the tabs to release the wire connector.
8
You’re now ready to install the new wrinkle guard switch.
9
Reattach the wire connector then insert the switch into the control panel and rotate counter-clockwise until it snaps into position.
10
Rotate the control panel back down, and snap it into place.
11
If applicable, replace the screws and end caps.
12
Reinstall the wrinkle guard knob and plug the appliance back in to make sure it’s functioning properly.
Description
This video provides step-by-step repair instructions for replacing the wrinkle shield rotary switch on a Whirlpool/Kenmore gas dryer. The most common reason for replacing the wrinkle shield switch is when clothes are coming out wrinkled.

All of the information for this wrinkle shield rotary switch replacement video is applicable to the following brands:
Whirlpool, Kenmore, Maytag, Amana, Crosley, Estate

Tools needed: hex socket, putty knife
Step-By-Step Instructions
1
As with any repair, be sure you unplug the appliance before beginning.
2
Your first step is to remove the wrinkle guard knob. This may require some effort - You can use string or wire to help pry it off.
3
Next, detach the control panel.
4
Depending on your model, you will either insert a putty knife under the panel to release the two clips or you will pull off both plastic end caps and remove the screws found underneath.
5
Now, rotate the control panel up.
6
Pull the tab and rotate the old switch to remove.
7
Squeeze the tabs to release the wire connector.
8
You’re now ready to install the new wrinkle guard switch.
9
Reattach the wire connector then insert the switch into the control panel and rotate counter-clockwise until it snaps into position.
10
Rotate the control panel back down, and snap it into place.
11
If applicable, replace the screws and end caps.
12
Reinstall the wrinkle guard knob and plug the appliance back in to make sure it’s functioning properly.

Applicable Product Model

icons/dryer
Brand
Product Type
Model
Subtype
Gas
Parts Needed
Switch
Switch
$69.70
Total$0.00

Related Articles & Videos

01:24
Part Replacement
Whirlpool Gas Dryer Valve Solenoid Coil 2 & 3 Terminal 694539
03:45
Part Replacement
Whirlpool/Kenmore Gas Dryer Pulley Wheel Replacement #279640
03:49
Part Replacement
Whirlpool/Kenmore Dryer Won't Start/Heat? Thermal Fuse #3392519
03:20
Part Replacement
Whirlpool/Kenmore Gas Dryer Belt Replacement #661570
03:52
Part Replacement
Whirlpool/Kenmore Dryer Drum Seal Replacement, Repair #280114