Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairGE Gas Range/Stove Surface Burner Orifice Holder #WB02K10361
GE Gas Range/Stove Surface Burner Orifice Holder #WB02K10361
Skill Level
Total Parts Cost
$17.29Estimated Savings
$150.0003:40
- Description
This video provides step-by-step repair instructions for replacing the surface burner orifice holder on a GE gas range. The most common reasons for replacing the orifice holder are when it is damaged or missing.
All of the information for this surface burner orifice holder replacement video is applicable to the following brands:
GE
All of the information for this surface burner orifice holder replacement video is applicable to the following brands:
GE
Step By Step Instructions
1
As with any appliance repair, you should unplug the power cord before beginning
2
Shut off the gas supply.
3
To replace the surface burner orifice holder in your range first remove all of the burner grates the burner caps and bases.
4
Now remove all of the screws securing the orifice holders to the main top.
5
Insert a putty knife under the main top to release the two spring clips.
6
Lift up the main top and pull the left mounting pin out of the slot first to remove the top.
7
Disconnect the appropriate spark igniter wire from the spark module.
8
Now detach the igniter from the spring clip and pull the wire through.
9
Use a 5/8th inch wrench to loosen the orifice holder retaining nut.
10
Unthread the nut and remove the old holder.
11
Prepare the new surface burner orifice holder for installation by transferring the spring clip from the old holder to the new one.
12
Position the new holder on the burner tube and secure it with the retaining nut.
13
Feed the igniter wire through the holder and snap the igniter into the spring clip.
14
Reconnect the wire to the spark module.
15
Replace the main top by inserting the right mounting pin into the hole in the bracket then position the left mounting pin into the slot.
16
Make sure the support rods are inserted into the side panel bushings then snap the main top into place.
17
Make sure the igniters protrude through the appropriate holes in the main top.
18
Align the screw holes then replace all of the screws to secure the holders.
19
Replace the burner bases by aligning the tab in the base with the notch in the main top.
20
Replace the burner caps and grates.
21
Make sure the bend in the grate frame faces the companion grate.
22
You’re now ready to turn the gas supply back on plug the power cord back in and confirm that the range is working properly.
Description
This video provides step-by-step repair instructions for replacing the surface burner orifice holder on a GE gas range. The most common reasons for replacing the orifice holder are when it is damaged or missing.
All of the information for this surface burner orifice holder replacement video is applicable to the following brands:
GE
All of the information for this surface burner orifice holder replacement video is applicable to the following brands:
GE
Step-By-Step Instructions
1
As with any appliance repair, you should unplug the power cord before beginning
2
Shut off the gas supply.
3
To replace the surface burner orifice holder in your range first remove all of the burner grates the burner caps and bases.
4
Now remove all of the screws securing the orifice holders to the main top.
5
Insert a putty knife under the main top to release the two spring clips.
6
Lift up the main top and pull the left mounting pin out of the slot first to remove the top.
7
Disconnect the appropriate spark igniter wire from the spark module.
8
Now detach the igniter from the spring clip and pull the wire through.
9
Use a 5/8th inch wrench to loosen the orifice holder retaining nut.
10
Unthread the nut and remove the old holder.
11
Prepare the new surface burner orifice holder for installation by transferring the spring clip from the old holder to the new one.
12
Position the new holder on the burner tube and secure it with the retaining nut.
13
Feed the igniter wire through the holder and snap the igniter into the spring clip.
14
Reconnect the wire to the spark module.
15
Replace the main top by inserting the right mounting pin into the hole in the bracket then position the left mounting pin into the slot.
16
Make sure the support rods are inserted into the side panel bushings then snap the main top into place.
17
Make sure the igniters protrude through the appropriate holes in the main top.
18
Align the screw holes then replace all of the screws to secure the holders.
19
Replace the burner bases by aligning the tab in the base with the notch in the main top.
20
Replace the burner caps and grates.
21
Make sure the bend in the grate frame faces the companion grate.
22
You’re now ready to turn the gas supply back on plug the power cord back in and confirm that the range is working properly.
Applicable Product Model
Total$0.00
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com