Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairGE Gas Stove Burner Won't Light? Spark Module #WB13K10029
GE Gas Stove Burner Won't Light? Spark Module #WB13K10029
Skill Level
Total Parts Cost
$59.19Estimated Savings
$112.5003:06
- Description
This video provides step-by-step instructions for replacing the spark module on GE gas ranges. The most common reasons for replacing the spark module are when there is a very weak spark, sparks happen only intermittently, the burner does not spark, or the burner sparks all the time.
All of the information in this spark module replacement video is applicable to the following brands: GE, Hotpoint
Tools used: multi-screwdriver, putty knife
All of the information in this spark module replacement video is applicable to the following brands: GE, Hotpoint
Tools used: multi-screwdriver, putty knife
Step By Step Instructions
1
As with any appliance repair, you should unplug the power cord before beginning
2
Shut off the gas supply.
3
To replace the spark module in your range first remove all of the burner grates the burner caps and bases.
4
Now remove all of the screws securing the orifice holders to the main top.
5
Insert a putty knife under the main top to release the two spring clips.
6
Lift up the main top and pull the left mounting pin out of the slot first to remove the top.
7
Note the orientation of the wires connected to the spark module then disconnect them.
8
Depress the tabs to release the old spark module from the rear panel.
9
Install the new spark module by aligning the tabs with the slots in the rear panel and snapping the module into place.
10
Connect the wires to the appropriate terminals on the new module.
11
Replace the main top by inserting the right mounting pin into the hole in the bracket then position the left mounting pin into the slot.
12
Make sure the support rods are inserted into the side panel bushings then snap the main top into place.
13
Make sure the igniters protrude through the appropriate holes in the main top.
14
Align the screw holes then replace all of the screws to secure the holders.
15
Replace the burner bases by aligning the tab in the base with the notch in the main top.
16
Replace the burner caps and grates.
17
Make sure the bend in the grate frame faces the companion grate.
18
You’re now ready to turn the gas supply back on plug the power cord back in and confirm that the range is working properly.
Description
This video provides step-by-step instructions for replacing the spark module on GE gas ranges. The most common reasons for replacing the spark module are when there is a very weak spark, sparks happen only intermittently, the burner does not spark, or the burner sparks all the time.
All of the information in this spark module replacement video is applicable to the following brands: GE, Hotpoint
Tools used: multi-screwdriver, putty knife
All of the information in this spark module replacement video is applicable to the following brands: GE, Hotpoint
Tools used: multi-screwdriver, putty knife
Step-By-Step Instructions
1
As with any appliance repair, you should unplug the power cord before beginning
2
Shut off the gas supply.
3
To replace the spark module in your range first remove all of the burner grates the burner caps and bases.
4
Now remove all of the screws securing the orifice holders to the main top.
5
Insert a putty knife under the main top to release the two spring clips.
6
Lift up the main top and pull the left mounting pin out of the slot first to remove the top.
7
Note the orientation of the wires connected to the spark module then disconnect them.
8
Depress the tabs to release the old spark module from the rear panel.
9
Install the new spark module by aligning the tabs with the slots in the rear panel and snapping the module into place.
10
Connect the wires to the appropriate terminals on the new module.
11
Replace the main top by inserting the right mounting pin into the hole in the bracket then position the left mounting pin into the slot.
12
Make sure the support rods are inserted into the side panel bushings then snap the main top into place.
13
Make sure the igniters protrude through the appropriate holes in the main top.
14
Align the screw holes then replace all of the screws to secure the holders.
15
Replace the burner bases by aligning the tab in the base with the notch in the main top.
16
Replace the burner caps and grates.
17
Make sure the bend in the grate frame faces the companion grate.
18
You’re now ready to turn the gas supply back on plug the power cord back in and confirm that the range is working properly.
Applicable Product Model
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com