Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairSamsung Dryer Motor & Blower Assembly Replacement DC93-00101F
Samsung Dryer Motor & Blower Assembly Replacement DC93-00101F
Skill Level
Total Parts Cost
$368.95Estimated Savings
$112.5007:22
- Description
This video provides step-by-step instructions for replacing the motor and blower assembly on Samsung dryers. The most common reason for replacing the motor and blower assembly is when the dryer gets too hot, runs too long, or won’t run.
All of the information in this motor and blower assembly replacement video is applicable to the following brands: Samsung
Tools used: multi-screwdriver, Phillips head bit, flat-head bit
All of the information in this motor and blower assembly replacement video is applicable to the following brands: Samsung
Tools used: multi-screwdriver, Phillips head bit, flat-head bit
Step By Step Instructions
1
As with any repair, be sure to unplug the appliance before beginning.
2
To replace the blower and motor assembly in your dryer, first remove the screws at the back securing the top panel.
3
Now slide the panel back and lift it off.
4
Next, carefully pull the control panel off from the top.
5
Disconnect the wire harness and set the panel aside.
6
Now remove the screws on top securing the front panel.
7
Open the dryer door and remove the remaining two front panel mounting screws.
8
Now use a flathead screwdriver to depress the locking tab and pull the front panel forward.
9
Disconnect the door switch wire and lift off the panel.
10
Next, remove the screws securing the support bracket.
11
Remove the wire harness from the twist retainers and set the bracket aside.
12
Disconnect the light bulb wire and remove the wire harness from the bulkhead twist retainers if you haven’t already done so.
13
Now, remove the screws securing the front bulkhead.
14
Remove the blower housing mounting screw as well.
15
Disconnect the moisture sensor wire harness.
16
You can now pull the bulkhead off.
17
Now reach under the drum and push the idler pulley to release the tension on the belt then unthread the belt from the pulley and motor shaft.
18
You can use the belt to help lift the drum out of the cabinet.
19
Next, disconnect the motor wire harness as well as the belt switch wire harness.
20
Detach the wires from the thermal limit and thermistor.
21
Now remove the screws securing the motor mounting bracket to the base.
22
You can now remove the old blower & motor assembly.
23
Install the new blower & motor assembly by inserting the mounting bracket tabs into the slots in the base while aligning the blower housing with the vent tube.
24
Replace the bracket mounting screws.
25
Connect the wires to the new thermal limit and thermistor.
26
Connect the wire harnesses to the belt switch and the motor.
27
Return the drum to the dryer cabinet and align it on the rear rollers.
28
Loop the belt around the pulley and motor shaft in a zig-zag formation.
29
Now, rotate the drum to help align the belt.
30
Reposition the front bulkhead on the cabinet frame.
31
Replace the mounting screws.
32
Replace the blower housing screw as well.
33
Reconnect the moisture sensor wire harness.
34
Reconnect the light bulb wire and secure it in the twist retainer.
35
Secure the wire harness in the bulkhead twist retainers.
36
Now secure the wire harness in the support bracket retainers.
37
Realign the support bracket and secure it with the screws.
38
Replace the front panel by aligning the slots in the panel with the tabs on the base.
39
Reconnect the wire to the door switch and snap the top half of the panel into position.
40
Replace all of the mounting screws.
41
Reconnect the wire harness on the control panel then align the tabs on the bottom of the control panel with the slots in the trim and snap the top edge into place.
42
Reposition the top panel by aligning the edge of the panel with the tabs on the support bracket then push forward.
43
Replace the screws in the back.
44
Plug the power cord back in and your dryer should be ready for use.
Description
This video provides step-by-step instructions for replacing the motor and blower assembly on Samsung dryers. The most common reason for replacing the motor and blower assembly is when the dryer gets too hot, runs too long, or won’t run.
All of the information in this motor and blower assembly replacement video is applicable to the following brands: Samsung
Tools used: multi-screwdriver, Phillips head bit, flat-head bit
All of the information in this motor and blower assembly replacement video is applicable to the following brands: Samsung
Tools used: multi-screwdriver, Phillips head bit, flat-head bit
Step-By-Step Instructions
1
As with any repair, be sure to unplug the appliance before beginning.
2
To replace the blower and motor assembly in your dryer, first remove the screws at the back securing the top panel.
3
Now slide the panel back and lift it off.
4
Next, carefully pull the control panel off from the top.
5
Disconnect the wire harness and set the panel aside.
6
Now remove the screws on top securing the front panel.
7
Open the dryer door and remove the remaining two front panel mounting screws.
8
Now use a flathead screwdriver to depress the locking tab and pull the front panel forward.
9
Disconnect the door switch wire and lift off the panel.
10
Next, remove the screws securing the support bracket.
11
Remove the wire harness from the twist retainers and set the bracket aside.
12
Disconnect the light bulb wire and remove the wire harness from the bulkhead twist retainers if you haven’t already done so.
13
Now, remove the screws securing the front bulkhead.
14
Remove the blower housing mounting screw as well.
15
Disconnect the moisture sensor wire harness.
16
You can now pull the bulkhead off.
17
Now reach under the drum and push the idler pulley to release the tension on the belt then unthread the belt from the pulley and motor shaft.
18
You can use the belt to help lift the drum out of the cabinet.
19
Next, disconnect the motor wire harness as well as the belt switch wire harness.
20
Detach the wires from the thermal limit and thermistor.
21
Now remove the screws securing the motor mounting bracket to the base.
22
You can now remove the old blower & motor assembly.
23
Install the new blower & motor assembly by inserting the mounting bracket tabs into the slots in the base while aligning the blower housing with the vent tube.
24
Replace the bracket mounting screws.
25
Connect the wires to the new thermal limit and thermistor.
26
Connect the wire harnesses to the belt switch and the motor.
27
Return the drum to the dryer cabinet and align it on the rear rollers.
28
Loop the belt around the pulley and motor shaft in a zig-zag formation.
29
Now, rotate the drum to help align the belt.
30
Reposition the front bulkhead on the cabinet frame.
31
Replace the mounting screws.
32
Replace the blower housing screw as well.
33
Reconnect the moisture sensor wire harness.
34
Reconnect the light bulb wire and secure it in the twist retainer.
35
Secure the wire harness in the bulkhead twist retainers.
36
Now secure the wire harness in the support bracket retainers.
37
Realign the support bracket and secure it with the screws.
38
Replace the front panel by aligning the slots in the panel with the tabs on the base.
39
Reconnect the wire to the door switch and snap the top half of the panel into position.
40
Replace all of the mounting screws.
41
Reconnect the wire harness on the control panel then align the tabs on the bottom of the control panel with the slots in the trim and snap the top edge into place.
42
Reposition the top panel by aligning the edge of the panel with the tabs on the support bracket then push forward.
43
Replace the screws in the back.
44
Plug the power cord back in and your dryer should be ready for use.
Applicable Product Model
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com