Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairSamsung Dryer Control & Display Board Replacement #DC92-00774M
Samsung Dryer Control & Display Board Replacement #DC92-00774M
Skill Level
Total Parts Cost
$407.49Estimated Savings
$112.5002:55
- Description
This video provides step-by-step repair instructions for replacing the user control and display board on a Samsung dryer. The most common reason for replacing the user control board is when the dryer has power but the control board dial and buttons are not responding.
All of the information for this user control board replacement video is applicable to the following brands:
Samsung
Tools needed: multi-screwdriver, Phillips head bit, string, flat head screwdriver
All of the information for this user control board replacement video is applicable to the following brands:
Samsung
Tools needed: multi-screwdriver, Phillips head bit, string, flat head screwdriver
Step By Step Instructions
1
As with any repair, be sure to unplug the appliance before beginning.
2
To replace the user control board assembly in your dryer, first remove the screws at the back securing the top panel.
3
Now slide the panel back and lift it off.
4
Next, carefully pull the control panel off from the top.
5
Disconnect the wire harness and set the panel on a sturdy surface.
6
Remove the selector knob – you can use string or wire to help pry it off.
7
Turn the control panel over and remove the mounting screws securing the control board assembly.
8
Now carefully separate the rear half of the display board from the front half and lift the display board and selector board off of the control panel.
9
Install the new user control board assembly by snapping the new rear half of the display board onto the front half then align the selector board on the control panel.
10
Replace the mounting screws.
11
Realign the selector knob on the stem and snap it onto the hub.
12
Connect the wire harness then align the tabs on the bottom of the control panel with the slots in the trim and snap the top edge into place.
13
Reposition the top panel by aligning the edge of the panel with the tabs on the support bracket then push forward.
14
Replace the screws in the back.
15
Plug the power cord back in and your dryer should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the user control and display board on a Samsung dryer. The most common reason for replacing the user control board is when the dryer has power but the control board dial and buttons are not responding.
All of the information for this user control board replacement video is applicable to the following brands:
Samsung
Tools needed: multi-screwdriver, Phillips head bit, string, flat head screwdriver
All of the information for this user control board replacement video is applicable to the following brands:
Samsung
Tools needed: multi-screwdriver, Phillips head bit, string, flat head screwdriver
Step-By-Step Instructions
1
As with any repair, be sure to unplug the appliance before beginning.
2
To replace the user control board assembly in your dryer, first remove the screws at the back securing the top panel.
3
Now slide the panel back and lift it off.
4
Next, carefully pull the control panel off from the top.
5
Disconnect the wire harness and set the panel on a sturdy surface.
6
Remove the selector knob – you can use string or wire to help pry it off.
7
Turn the control panel over and remove the mounting screws securing the control board assembly.
8
Now carefully separate the rear half of the display board from the front half and lift the display board and selector board off of the control panel.
9
Install the new user control board assembly by snapping the new rear half of the display board onto the front half then align the selector board on the control panel.
10
Replace the mounting screws.
11
Realign the selector knob on the stem and snap it onto the hub.
12
Connect the wire harness then align the tabs on the bottom of the control panel with the slots in the trim and snap the top edge into place.
13
Reposition the top panel by aligning the edge of the panel with the tabs on the support bracket then push forward.
14
Replace the screws in the back.
15
Plug the power cord back in and your dryer should be ready for use.
Applicable Product Model
Parts Needed
Total$0.00
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com