Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairFrigidaire Washer Drain Pump Replacement #137221600
Frigidaire Washer Drain Pump Replacement #137221600
Skill Level
Total Parts Cost
$157.95Estimated Savings
$112.5003:19
- Description
This video provides step-by-step instructions for replacing the drain pump on Frigidaire Affinity front-load washing machines. The most common reasons for replacing the drain pump are when the washer is not draining or is leaking water.
All of the information in this drain pump replacement video is applicable to the following brands: Frigidaire, Crosley, Electrolux
Tools used: screwdriver, needle-nose pliers
All of the information in this drain pump replacement video is applicable to the following brands: Frigidaire, Crosley, Electrolux
Tools used: screwdriver, needle-nose pliers
Step By Step Instructions
1
As with any repair, be sure you unplug the appliance before beginning.
2
To replace the drain pump in your washer…
3
…first remove the screws securing the lower front access panel.
4
Pull the panel off.
5
Use pliers to release the retaining clamps securing the inlet and outlet hoses to the pump….
6
…and pull the hoses off – be prepared for some water to spill out.
7
Now use a 5/16th inch socket to remove the mounting screws securing the pump to the base.
8
Pull the pump away from the base and disconnect the wire harness.
9
Before you install the new drain pump…
10
…you may need to reposition the impeller housing and transfer the bracket from the old pump to the new one.
11
To do this, first pull the shield off…
12
…and remove the screws to release the bracket from the new pump.
13
Now remove the remaining screws securing the impeller housing.
14
Pull the housing off and rotate it 180 degrees so the outlet port faces the opposite direction from the wire terminals.
15
Replace the screws to secure.
16
Remove the screws to release the bracket from the old pump and transfer it to the new pump.
17
Secure it with the screws.
18
Slide the shield into position.
19
Now connect the wire harness to the new pump…and secure the wires.
20
Position the pump on the base…
21
…and replace the mounting screws.
22
Attach the inlet and outlet hoses to the appropriate ports on the new pump…
23
…and position the retaining clamps to secure.
24
Replace the access panel by aligning the holes with the pins on the bottom of the front panel…
25
…then replace the screws.
26
You’re now ready to plug the power cord back in…
27
…and confirm that the washer works properly.
Description
This video provides step-by-step instructions for replacing the drain pump on Frigidaire Affinity front-load washing machines. The most common reasons for replacing the drain pump are when the washer is not draining or is leaking water.
All of the information in this drain pump replacement video is applicable to the following brands: Frigidaire, Crosley, Electrolux
Tools used: screwdriver, needle-nose pliers
All of the information in this drain pump replacement video is applicable to the following brands: Frigidaire, Crosley, Electrolux
Tools used: screwdriver, needle-nose pliers
Step-By-Step Instructions
1
As with any repair, be sure you unplug the appliance before beginning.
2
To replace the drain pump in your washer…
3
…first remove the screws securing the lower front access panel.
4
Pull the panel off.
5
Use pliers to release the retaining clamps securing the inlet and outlet hoses to the pump….
6
…and pull the hoses off – be prepared for some water to spill out.
7
Now use a 5/16th inch socket to remove the mounting screws securing the pump to the base.
8
Pull the pump away from the base and disconnect the wire harness.
9
Before you install the new drain pump…
10
…you may need to reposition the impeller housing and transfer the bracket from the old pump to the new one.
11
To do this, first pull the shield off…
12
…and remove the screws to release the bracket from the new pump.
13
Now remove the remaining screws securing the impeller housing.
14
Pull the housing off and rotate it 180 degrees so the outlet port faces the opposite direction from the wire terminals.
15
Replace the screws to secure.
16
Remove the screws to release the bracket from the old pump and transfer it to the new pump.
17
Secure it with the screws.
18
Slide the shield into position.
19
Now connect the wire harness to the new pump…and secure the wires.
20
Position the pump on the base…
21
…and replace the mounting screws.
22
Attach the inlet and outlet hoses to the appropriate ports on the new pump…
23
…and position the retaining clamps to secure.
24
Replace the access panel by aligning the holes with the pins on the bottom of the front panel…
25
…then replace the screws.
26
You’re now ready to plug the power cord back in…
27
…and confirm that the washer works properly.
Applicable Product Model
Parts Needed
Drain Pump
$157.95
Total$0.00
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com