Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairWeed Eater Edger On/Off Switch Replacement #530053920
Weed Eater Edger On/Off Switch Replacement #530053920
Skill Level
Total Parts Cost
$16.44Estimated Savings
$112.5004:51
- Description
This video provides step-by-step repair instructions for replacing the on/off switch on a Weed Eater edger. The most common reason for replacing the on/off switch is when the edger won’t start.
All of the information for this on/off switch replacement video is applicable to the following brands:
Craftsman, Weed Eater
Tools used: T25 Torx bit screwdriver, flat head screwdriver, spark plug wrench, needle-nose pliers
All of the information for this on/off switch replacement video is applicable to the following brands:
Craftsman, Weed Eater
Tools used: T25 Torx bit screwdriver, flat head screwdriver, spark plug wrench, needle-nose pliers
Step By Step Instructions
1
In this video, we will show one or more of these icons to alert you when to use caution before you replace the on/off switch on your edger.
2
First, make sure the engine has cooled.
3
Next, remove the wire and boot from the spark plug to prevent the engine from accidentally starting.
4
We recommend performing this procedure with little or no fuel in the tank.
5
Use a T25 Torx bit screwdriver to remove the screws securing the throttle cable.
6
Note the location of the cable on the throttle plate, then detach the cable.
7
Note the orientation of the fuel lines attached to the carburetor, then detach them.
8
Next, unthread the mounting screws securing the carburetor.
9
Pull off the air box and remove the carburetor.
10
Now, remove the screws to release the carburetor adapter.
11
Use a socket or a spark plug wrench to help unthread the spark plug.
12
Remove the screws securing the engine cover.
13
Pull the cover off.
14
Note the location of the on/off switch wires, then detach them.
15
Now, slide the old switch out of the housing.
16
Install the new on/off switch by sliding it into place on the housing.
17
Attach the wires to the appropriate terminals on the new switch.
18
Reposition the engine cover and replace the screws to secure.
19
Rethread the spark plug, being careful not to over-tighten the plug.
20
Realign the carburetor adapter and secure it with the screws.
21
Replace the adapter gasket.
22
Now, realign the airbox.
23
Reposition the carburetor between the box and the adapter, then insert the upper mounting screw and thread it loosely.
24
Insert and thread the lower mounting screw and tighten both screws to secure.
25
Attach the fuel lines to the appropriate ports on the carburetor.
26
Attach the throttle cable to the appropriate hold in the throttle plate.
27
Insert the cable into the slot in the airbox and replace the screw to secure.
28
With the repair completed, reattach the spark plug wire and boot.
29
Refill the tank with fuel, and your edger should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the on/off switch on a Weed Eater edger. The most common reason for replacing the on/off switch is when the edger won’t start.
All of the information for this on/off switch replacement video is applicable to the following brands:
Craftsman, Weed Eater
Tools used: T25 Torx bit screwdriver, flat head screwdriver, spark plug wrench, needle-nose pliers
All of the information for this on/off switch replacement video is applicable to the following brands:
Craftsman, Weed Eater
Tools used: T25 Torx bit screwdriver, flat head screwdriver, spark plug wrench, needle-nose pliers
Step-By-Step Instructions
1
In this video, we will show one or more of these icons to alert you when to use caution before you replace the on/off switch on your edger.
2
First, make sure the engine has cooled.
3
Next, remove the wire and boot from the spark plug to prevent the engine from accidentally starting.
4
We recommend performing this procedure with little or no fuel in the tank.
5
Use a T25 Torx bit screwdriver to remove the screws securing the throttle cable.
6
Note the location of the cable on the throttle plate, then detach the cable.
7
Note the orientation of the fuel lines attached to the carburetor, then detach them.
8
Next, unthread the mounting screws securing the carburetor.
9
Pull off the air box and remove the carburetor.
10
Now, remove the screws to release the carburetor adapter.
11
Use a socket or a spark plug wrench to help unthread the spark plug.
12
Remove the screws securing the engine cover.
13
Pull the cover off.
14
Note the location of the on/off switch wires, then detach them.
15
Now, slide the old switch out of the housing.
16
Install the new on/off switch by sliding it into place on the housing.
17
Attach the wires to the appropriate terminals on the new switch.
18
Reposition the engine cover and replace the screws to secure.
19
Rethread the spark plug, being careful not to over-tighten the plug.
20
Realign the carburetor adapter and secure it with the screws.
21
Replace the adapter gasket.
22
Now, realign the airbox.
23
Reposition the carburetor between the box and the adapter, then insert the upper mounting screw and thread it loosely.
24
Insert and thread the lower mounting screw and tighten both screws to secure.
25
Attach the fuel lines to the appropriate ports on the carburetor.
26
Attach the throttle cable to the appropriate hold in the throttle plate.
27
Insert the cable into the slot in the airbox and replace the screw to secure.
28
With the repair completed, reattach the spark plug wire and boot.
29
Refill the tank with fuel, and your edger should be ready for use.
Applicable Product Model
Total$0.00
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com