Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairSamsung Dishwasher Mounting Bracket Replacement #DD94-01002A
Samsung Dishwasher Mounting Bracket Replacement #DD94-01002A
Skill Level
Total Parts Cost
$16.59Estimated Savings
$112.5005:47
- Description
This video provides step-by-step repair instructions for replacing the mounting brackets on a Samsung dishwasher. The most common reason for replacing the mounting brackets is if they are broken.
All of the information for this mounting bracket replacement video is applicable to the following brands:
Samsung
Tools needed: phillips head screwdriver, flat head screwdriver, 5/8 inch wrench, 9/64 inch hex head screwdriver, pliers
All of the information for this mounting bracket replacement video is applicable to the following brands:
Samsung
Tools needed: phillips head screwdriver, flat head screwdriver, 5/8 inch wrench, 9/64 inch hex head screwdriver, pliers
Step By Step Instructions
1
To replace the mounting brackets on your dishwasher, you will need to pull the dishwasher a few inches away from the cabinet.
2
If the water supply and power supply lines do not provide enough slack, to do this, you will need to fully uninstall the appliance.
3
To do this, turn off the power to your dishwasher and shut off the water supply valve.
4
Use a Phillips head screwdriver to remove the screws securing the lower access panel.
5
Remove the panel.
6
Use a 5/8 inch wrench to help unthread the water supply line from the inlet valve.
7
Be prepared for some water to spill.
8
Next, unthread the screws securing the junction box cover, then pull the cover off.
9
Note the location of the wires, then untwist the wire nuts to disconnect the wires.
10
Unthread the strain relief nut and detach the strain relief from the junction box.
11
Next, disconnect the drain hose from the sink drain or garbage disposer and feed it through the cabinet.
12
Open the dishwasher door and remove the mounting bracket screws.
13
To move the dishwasher, you may need to adjust the legs.
14
To lower the appliance, you can lower the rear leveling leg by using a 9/64 inch hex head screwdriver to rotate the adjustment rod at the front clockwise.
15
Now, very carefully pull the dishwasher away from the cabinet.
16
Remove the old brackets, if still intact.
17
Install the new mounting brackets by inserting the tabs into the slots in the frame.
18
Make sure the drain hose is accessible through the cabinet wall, then gently slide the dishwasher back into the cabinet.
19
Adjust the leveling legs if necessary.
20
Replace the screws to secure the mounting brackets to the cabinet or countertop.
21
Feed the drain hose through the cabinet and connect it to the sink drain or disposer.
22
Make sure the hose is elevated above the connection point.
23
Fully position the wire strain relief in the junction box and secure the strain relief nut.
24
Join the wires together and secure them with the wire nuts.
25
Align the cover and replace the screw to secure.
26
Reconnect the water supply line to the inlet valve.
27
Replace the lower access panel and secure it with the screws.
28
With the repair completed, turn the water supply back on as well as the power, and your dishwasher should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the mounting brackets on a Samsung dishwasher. The most common reason for replacing the mounting brackets is if they are broken.
All of the information for this mounting bracket replacement video is applicable to the following brands:
Samsung
Tools needed: phillips head screwdriver, flat head screwdriver, 5/8 inch wrench, 9/64 inch hex head screwdriver, pliers
All of the information for this mounting bracket replacement video is applicable to the following brands:
Samsung
Tools needed: phillips head screwdriver, flat head screwdriver, 5/8 inch wrench, 9/64 inch hex head screwdriver, pliers
Step-By-Step Instructions
1
To replace the mounting brackets on your dishwasher, you will need to pull the dishwasher a few inches away from the cabinet.
2
If the water supply and power supply lines do not provide enough slack, to do this, you will need to fully uninstall the appliance.
3
To do this, turn off the power to your dishwasher and shut off the water supply valve.
4
Use a Phillips head screwdriver to remove the screws securing the lower access panel.
5
Remove the panel.
6
Use a 5/8 inch wrench to help unthread the water supply line from the inlet valve.
7
Be prepared for some water to spill.
8
Next, unthread the screws securing the junction box cover, then pull the cover off.
9
Note the location of the wires, then untwist the wire nuts to disconnect the wires.
10
Unthread the strain relief nut and detach the strain relief from the junction box.
11
Next, disconnect the drain hose from the sink drain or garbage disposer and feed it through the cabinet.
12
Open the dishwasher door and remove the mounting bracket screws.
13
To move the dishwasher, you may need to adjust the legs.
14
To lower the appliance, you can lower the rear leveling leg by using a 9/64 inch hex head screwdriver to rotate the adjustment rod at the front clockwise.
15
Now, very carefully pull the dishwasher away from the cabinet.
16
Remove the old brackets, if still intact.
17
Install the new mounting brackets by inserting the tabs into the slots in the frame.
18
Make sure the drain hose is accessible through the cabinet wall, then gently slide the dishwasher back into the cabinet.
19
Adjust the leveling legs if necessary.
20
Replace the screws to secure the mounting brackets to the cabinet or countertop.
21
Feed the drain hose through the cabinet and connect it to the sink drain or disposer.
22
Make sure the hose is elevated above the connection point.
23
Fully position the wire strain relief in the junction box and secure the strain relief nut.
24
Join the wires together and secure them with the wire nuts.
25
Align the cover and replace the screw to secure.
26
Reconnect the water supply line to the inlet valve.
27
Replace the lower access panel and secure it with the screws.
28
With the repair completed, turn the water supply back on as well as the power, and your dishwasher should be ready for use.
Applicable Product Model
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com