Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairElectrolux Washer Dispenser Housing Replacement #134964020
Electrolux Washer Dispenser Housing Replacement #134964020
Skill Level
Total Parts Cost
$246.42Estimated Savings
$112.5007:59
- Description
This video provides step-by-step repair instructions for replacing the dispenser housing on an Electrolux washing machine. The most common reasons for replacing the dispenser are the washer not filling with soap or not filling at all.
All of the information for this dispenser housing replacement video is applicable to the following brands:
Electrolux
Tools needed: phillips head screwdriver, #2 square bit, T-20 Torx bit
All of the information for this dispenser housing replacement video is applicable to the following brands:
Electrolux
Tools needed: phillips head screwdriver, #2 square bit, T-20 Torx bit
Step By Step Instructions
1
Before you replace the dispenser housing in your washer be sure to unplug the power cord and close the water supply valves.
2
Remove the hot and cold water supply lines from the inlet valve – be prepared for some water to spill out.
3
Use a number two square bit or a phillips-head screwdriver to unthread the screws at the back securing the main top.
4
Slide the main top back and lift it up to remove.
5
Next, unthread the two screws securing the vibration dampener.
6
Lift off the block.
7
Disconnect the power cord wire connecter detach the grounding wire from the rear panel and release the wire retainer.
8
Unthread the mounting screw securing the drain hose retainer and remove the retainer.
9
Next, remove the screws securing the main top mounting bracket.
10
Set the bracket aside.
11
Unthread the screw securing the rear panel to the motor control board.
12
Now use a t-20 torx bit to unthread the remaining screws securing the rear panel.
13
Detach the panel.
14
Pull out the dispenser drawer and depress the button to fully release it.
15
Unthread the dispenser housing mounting screws.
16
Use a phillips-head screwdriver to loosen the screw to release the retaining clamp securing the hose to the dispenser.
17
Pull the hose off.
18
Disconnect the water inlet valve wire connecters.
19
Next, unthread the two screws securing the dispenser housing to the support rail.
20
Now slide the old housing straight back to detach.
21
Cut the zip tie securing the recirculation and air vent hoses.
22
Release the spring clamp securing the air vent hose to the housing and pull the hose off to remove the housing.
23
Prepare the new dispenser housing for installation by transferring the vent tube from the old housing to the new one.
24
Attach the air vent hose to the port on the new dispenser housing and secure it with the spring clamp.
25
Use a zip tie to secure the air vent and recirculation hoses to the housing.
26
Now, aligning the groove in the housing with the tab on the support rail slide the housing into place.
27
Thread the screws to secure the housing to the support rail.
28
Connect the wire connecters to the appropriate terminals on the water inlet valve.
29
Attach the dispenser hose to the housing – make sure the indicator tab aligns with the arrow.
30
Tighten the screw to secure the clamp.
31
Replace the screws in the dispenser drawer housing.
32
Replace the dispenser drawer.
33
Reposition the rear panel.
34
Thread and tighten all of the mounting screws except for the two top screws on the back.
35
Realign the main top support bracket and secure it with the screws.
36
Reconnect the power cord wire connecter Attach the grounding wire to the rear panel and snap the wire retainer into place.
37
Realign the drain hose retainer and replace the mounting screw.
38
Reposition the vibration dampener then thread and tighten the screws to secure.
39
Realign the main top and slide it into place.
40
Rethread the screws in the back.
41
Reattach the hot and cold water supply lines to the inlet valve.
42
With the repair completed reopen the water supply valves plug the power cord back in and your washer should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the dispenser housing on an Electrolux washing machine. The most common reasons for replacing the dispenser are the washer not filling with soap or not filling at all.
All of the information for this dispenser housing replacement video is applicable to the following brands:
Electrolux
Tools needed: phillips head screwdriver, #2 square bit, T-20 Torx bit
All of the information for this dispenser housing replacement video is applicable to the following brands:
Electrolux
Tools needed: phillips head screwdriver, #2 square bit, T-20 Torx bit
Step-By-Step Instructions
1
Before you replace the dispenser housing in your washer be sure to unplug the power cord and close the water supply valves.
2
Remove the hot and cold water supply lines from the inlet valve – be prepared for some water to spill out.
3
Use a number two square bit or a phillips-head screwdriver to unthread the screws at the back securing the main top.
4
Slide the main top back and lift it up to remove.
5
Next, unthread the two screws securing the vibration dampener.
6
Lift off the block.
7
Disconnect the power cord wire connecter detach the grounding wire from the rear panel and release the wire retainer.
8
Unthread the mounting screw securing the drain hose retainer and remove the retainer.
9
Next, remove the screws securing the main top mounting bracket.
10
Set the bracket aside.
11
Unthread the screw securing the rear panel to the motor control board.
12
Now use a t-20 torx bit to unthread the remaining screws securing the rear panel.
13
Detach the panel.
14
Pull out the dispenser drawer and depress the button to fully release it.
15
Unthread the dispenser housing mounting screws.
16
Use a phillips-head screwdriver to loosen the screw to release the retaining clamp securing the hose to the dispenser.
17
Pull the hose off.
18
Disconnect the water inlet valve wire connecters.
19
Next, unthread the two screws securing the dispenser housing to the support rail.
20
Now slide the old housing straight back to detach.
21
Cut the zip tie securing the recirculation and air vent hoses.
22
Release the spring clamp securing the air vent hose to the housing and pull the hose off to remove the housing.
23
Prepare the new dispenser housing for installation by transferring the vent tube from the old housing to the new one.
24
Attach the air vent hose to the port on the new dispenser housing and secure it with the spring clamp.
25
Use a zip tie to secure the air vent and recirculation hoses to the housing.
26
Now, aligning the groove in the housing with the tab on the support rail slide the housing into place.
27
Thread the screws to secure the housing to the support rail.
28
Connect the wire connecters to the appropriate terminals on the water inlet valve.
29
Attach the dispenser hose to the housing – make sure the indicator tab aligns with the arrow.
30
Tighten the screw to secure the clamp.
31
Replace the screws in the dispenser drawer housing.
32
Replace the dispenser drawer.
33
Reposition the rear panel.
34
Thread and tighten all of the mounting screws except for the two top screws on the back.
35
Realign the main top support bracket and secure it with the screws.
36
Reconnect the power cord wire connecter Attach the grounding wire to the rear panel and snap the wire retainer into place.
37
Realign the drain hose retainer and replace the mounting screw.
38
Reposition the vibration dampener then thread and tighten the screws to secure.
39
Realign the main top and slide it into place.
40
Rethread the screws in the back.
41
Reattach the hot and cold water supply lines to the inlet valve.
42
With the repair completed reopen the water supply valves plug the power cord back in and your washer should be ready for use.
Applicable Product Model
Recommended Tools and Accessories
Cleaner
$7.62
Total$0.00
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com