Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairHusqvarna Leaf Blower Impeller Blade Replacement #502850201
Husqvarna Leaf Blower Impeller Blade Replacement #502850201
Skill Level
Total Parts Cost
$34.80Estimated Savings
$112.5004:45
- Description
This video provides step-by-step repair instructions for replacing the impeller blade on a Husqvarna leaf blower. The most common reasons for replacing the blade are if the leaf blower is vibrating heavily or if there is not much air being expelled by the leaf blower.
All of the information in this impeller blade replacement video is applicable to following brands: Husqvarna
Tools used: T-27 Torx bit, flat head screwdriver, 10mm socket
All of the information in this impeller blade replacement video is applicable to following brands: Husqvarna
Tools used: T-27 Torx bit, flat head screwdriver, 10mm socket
Step By Step Instructions
1
Before you replace the impeller blade in your leaf blower make sure the engine has cooled.
2
Next, you should remove the wire and boot from the spark plug to prevent the engine from accidentally starting.
3
We recommend performing this procedure with no fuel in the tank.
4
Note the orientation of the primer and intake hoses then disconnect them from the carburetor.
5
Set the leaf blower on its side and use a 10mm socket to unthread the mounting nuts securing the blower assembly to the frame.
6
Return the blower to its upright position and use a t-27 torx bit to unthread the screws to release the blower assembly support.
7
Remove the blower assembly from the frame and set it on its side.
8
Remove the nuts and bolts securing the blower hose to the housing.
9
Use the t-27 torx bit or a flat-head screwdriver to unthread the remaining screws securing the two halves of the housing.
10
Separate the housing and set the hose assembly aside.
11
Remove the impeller blade mounting bolts.
12
Lift off the old blade.
13
Install the new impeller blade by aligning it on the flywheel.
14
Thread and tighten the mounting bolts to secure.
15
Confirm that the blower assembly mounts are in place then reposition the blower hose assembly and join the two halves of the housing together.
16
Replace the screws to secure.
17
Secure the nuts and bolts as well.
18
Reposition the blower assembly in the frame and rethread the screws into the support.
19
Set the blower on its side then thread and tighten the mounting nuts on the bottom.
20
Return the blower to its upright position and reconnect the intake and primer hoses to the appropriate ports on the carburetor.
21
With the repair completed reattach the wire and boot to the spark plug refill the fuel tank and your leaf blower should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the impeller blade on a Husqvarna leaf blower. The most common reasons for replacing the blade are if the leaf blower is vibrating heavily or if there is not much air being expelled by the leaf blower.
All of the information in this impeller blade replacement video is applicable to following brands: Husqvarna
Tools used: T-27 Torx bit, flat head screwdriver, 10mm socket
All of the information in this impeller blade replacement video is applicable to following brands: Husqvarna
Tools used: T-27 Torx bit, flat head screwdriver, 10mm socket
Step-By-Step Instructions
1
Before you replace the impeller blade in your leaf blower make sure the engine has cooled.
2
Next, you should remove the wire and boot from the spark plug to prevent the engine from accidentally starting.
3
We recommend performing this procedure with no fuel in the tank.
4
Note the orientation of the primer and intake hoses then disconnect them from the carburetor.
5
Set the leaf blower on its side and use a 10mm socket to unthread the mounting nuts securing the blower assembly to the frame.
6
Return the blower to its upright position and use a t-27 torx bit to unthread the screws to release the blower assembly support.
7
Remove the blower assembly from the frame and set it on its side.
8
Remove the nuts and bolts securing the blower hose to the housing.
9
Use the t-27 torx bit or a flat-head screwdriver to unthread the remaining screws securing the two halves of the housing.
10
Separate the housing and set the hose assembly aside.
11
Remove the impeller blade mounting bolts.
12
Lift off the old blade.
13
Install the new impeller blade by aligning it on the flywheel.
14
Thread and tighten the mounting bolts to secure.
15
Confirm that the blower assembly mounts are in place then reposition the blower hose assembly and join the two halves of the housing together.
16
Replace the screws to secure.
17
Secure the nuts and bolts as well.
18
Reposition the blower assembly in the frame and rethread the screws into the support.
19
Set the blower on its side then thread and tighten the mounting nuts on the bottom.
20
Return the blower to its upright position and reconnect the intake and primer hoses to the appropriate ports on the carburetor.
21
With the repair completed reattach the wire and boot to the spark plug refill the fuel tank and your leaf blower should be ready for use.
Applicable Product Model
Parts Needed
Fan Blade
$34.80
Total$0.00
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com