Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairDryer Makes Noise? Maytag Dryer Repair #12001541
Dryer Makes Noise? Maytag Dryer Repair #12001541
Skill Level
Total Parts Cost
$24.77Estimated Savings
$112.5003:29
- Description
This video provides step-by-step instructions for replacing the drum support roller on Maytag dryers. The most common reasons for replacing the drum support roller are when the dryer makes noise, stops turning during the cycle, or won’t turn at all.
All of the information for this roller replacement video is applicable to the following brands: Maytag, Jenn Air, Crosley
Tools needed: screwdriver, snap ring pliers
All of the information for this roller replacement video is applicable to the following brands: Maytag, Jenn Air, Crosley
Tools needed: screwdriver, snap ring pliers
Step By Step Instructions
1
As with any repair, be sure you unplug the appliance before beginning.
2
Your first step is to remove the screws at the bottom of the front panel.
3
Now, rotate the panel out from the bottom to release the clips at the top.
4
Noting their location, disconnect the wires from the door switch as well as from the retaining clip on the panel and set the panel aside.
5
Release the wires from the front bulkhead.
6
Next, remove the screws to release the front bulkhead from the cabinet.
7
Reach under the drum and push the idler pulley up to release the belt tension.
8
Unthread the belt from the pulley and motor shaft and pull the belt out.
9
Now lift out the drum to access the support rollers.
10
Use snap ring pliers to release the snap ring then pull off the old washers and roller from the axle.
11
Prepare to install the new roller by first using a cloth to clean off the axle.
12
Now, slide one of the new washers onto the axle followed by the new roller.
13
Slide the second washer on and secure with the snap ring.
14
Replace the drum by aligning its rim on the two support rollers
15
Slide the belt over the drum, flat-side down and loop the belt around the pulley and motor shaft in a zig-zag formation.
16
Now rotate the drum to help align the belt.
17
Position the front bulkhead and secure it with the screws.
18
Secure the door switch wires on the retaining clips of both the bulkhead and the front panel then reconnect the wires to the door switch.
19
Position the front panel clips under the lip of the main top and rotate the panel into place.
20
Secure it with the mounting screws.
21
You’re now ready to plug the appliance back in to make sure it’s functioning properly.
Description
This video provides step-by-step instructions for replacing the drum support roller on Maytag dryers. The most common reasons for replacing the drum support roller are when the dryer makes noise, stops turning during the cycle, or won’t turn at all.
All of the information for this roller replacement video is applicable to the following brands: Maytag, Jenn Air, Crosley
Tools needed: screwdriver, snap ring pliers
All of the information for this roller replacement video is applicable to the following brands: Maytag, Jenn Air, Crosley
Tools needed: screwdriver, snap ring pliers
Step-By-Step Instructions
1
As with any repair, be sure you unplug the appliance before beginning.
2
Your first step is to remove the screws at the bottom of the front panel.
3
Now, rotate the panel out from the bottom to release the clips at the top.
4
Noting their location, disconnect the wires from the door switch as well as from the retaining clip on the panel and set the panel aside.
5
Release the wires from the front bulkhead.
6
Next, remove the screws to release the front bulkhead from the cabinet.
7
Reach under the drum and push the idler pulley up to release the belt tension.
8
Unthread the belt from the pulley and motor shaft and pull the belt out.
9
Now lift out the drum to access the support rollers.
10
Use snap ring pliers to release the snap ring then pull off the old washers and roller from the axle.
11
Prepare to install the new roller by first using a cloth to clean off the axle.
12
Now, slide one of the new washers onto the axle followed by the new roller.
13
Slide the second washer on and secure with the snap ring.
14
Replace the drum by aligning its rim on the two support rollers
15
Slide the belt over the drum, flat-side down and loop the belt around the pulley and motor shaft in a zig-zag formation.
16
Now rotate the drum to help align the belt.
17
Position the front bulkhead and secure it with the screws.
18
Secure the door switch wires on the retaining clips of both the bulkhead and the front panel then reconnect the wires to the door switch.
19
Position the front panel clips under the lip of the main top and rotate the panel into place.
20
Secure it with the mounting screws.
21
You’re now ready to plug the appliance back in to make sure it’s functioning properly.
Applicable Product Model
Parts Needed
Drum Roller
$24.77
Total$0.00
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com