Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairMaytag Dryer Idler Pulley Replacement, Dryer Repair #6-3037050
Maytag Dryer Idler Pulley Replacement, Dryer Repair #6-3037050
Skill Level
Total Parts Cost
$18.34Estimated Savings
$112.5003:34
- Description
This video provides step-by-step instructions for replacing the idler pulley on Maytag dryers. The most common reasons for replacing the idler pulley are when the pulley makes noise or the drum will not turn.
All the information in this idler pulley replacement video is applicable to the following brands: Kenmore, Whirlpool, KitchenAid, Roper, Estate, Maytag, Crosley, Inglis, Amana, Admiral
Tools used: hex socket, flat-head screwdriver, Phillips head screwdriver, putty knife
All the information in this idler pulley replacement video is applicable to the following brands: Kenmore, Whirlpool, KitchenAid, Roper, Estate, Maytag, Crosley, Inglis, Amana, Admiral
Tools used: hex socket, flat-head screwdriver, Phillips head screwdriver, putty knife
Step By Step Instructions
1
As with any repair, be sure you unplug the appliance before beginning.
2
Your first step is to remove the screws at the bottom of the front panel.
3
Now, rotate the panel out from the bottom to release the clips at the top.
4
Noting their location, disconnect the wires from the door switch as well as from the retaining clip on the panel and set the panel aside.
5
Release the wires from the front bulkhead.
6
Next, remove the screws to release the front bulkhead from the cabinet.
7
Reach under the drum and push the idler pulley up to release the belt tension.
8
Unthread the belt from the pulley and motor shaft and pull the belt out.
9
Now lift out the drum.
10
Use needle-nose pliers to remove the “c” clip then pull off the washer and the old pulley.
11
Prepare to install the new pulley by first using a cloth to clean off the idler shaft then slide the new pulley on.
12
Replace the washer and secure with the “c” clip.
13
Replace the drum by aligning its rim on the two support rollers
14
Slide the belt over the drum, flat-side down and loop the belt around the pulley and motor shaft in a zig-zag formation.
15
Now rotate the drum to help align the belt.
16
Position the front bulkhead and secure it with the screws.
17
Secure the door switch wires on the retaining clips of both the bulkhead and the front panel then reconnect the wires to the door switch.
18
Position the front panel clips under the lip of the main top and rotate the panel into place.
19
Secure it with the mounting screws.
20
You’re now ready to plug the appliance back in to make sure it’s functioning properly.
Description
This video provides step-by-step instructions for replacing the idler pulley on Maytag dryers. The most common reasons for replacing the idler pulley are when the pulley makes noise or the drum will not turn.
All the information in this idler pulley replacement video is applicable to the following brands: Kenmore, Whirlpool, KitchenAid, Roper, Estate, Maytag, Crosley, Inglis, Amana, Admiral
Tools used: hex socket, flat-head screwdriver, Phillips head screwdriver, putty knife
All the information in this idler pulley replacement video is applicable to the following brands: Kenmore, Whirlpool, KitchenAid, Roper, Estate, Maytag, Crosley, Inglis, Amana, Admiral
Tools used: hex socket, flat-head screwdriver, Phillips head screwdriver, putty knife
Step-By-Step Instructions
1
As with any repair, be sure you unplug the appliance before beginning.
2
Your first step is to remove the screws at the bottom of the front panel.
3
Now, rotate the panel out from the bottom to release the clips at the top.
4
Noting their location, disconnect the wires from the door switch as well as from the retaining clip on the panel and set the panel aside.
5
Release the wires from the front bulkhead.
6
Next, remove the screws to release the front bulkhead from the cabinet.
7
Reach under the drum and push the idler pulley up to release the belt tension.
8
Unthread the belt from the pulley and motor shaft and pull the belt out.
9
Now lift out the drum.
10
Use needle-nose pliers to remove the “c” clip then pull off the washer and the old pulley.
11
Prepare to install the new pulley by first using a cloth to clean off the idler shaft then slide the new pulley on.
12
Replace the washer and secure with the “c” clip.
13
Replace the drum by aligning its rim on the two support rollers
14
Slide the belt over the drum, flat-side down and loop the belt around the pulley and motor shaft in a zig-zag formation.
15
Now rotate the drum to help align the belt.
16
Position the front bulkhead and secure it with the screws.
17
Secure the door switch wires on the retaining clips of both the bulkhead and the front panel then reconnect the wires to the door switch.
18
Position the front panel clips under the lip of the main top and rotate the panel into place.
19
Secure it with the mounting screws.
20
You’re now ready to plug the appliance back in to make sure it’s functioning properly.
Applicable Product Model
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com