Video & Articles: Appliance & Equipment RepairFrigidaire Refrigerator Replace Dispenser Actuator #5304501181

Frigidaire Refrigerator Replace Dispenser Actuator #5304501181

03:13
This video provides step-by-step repair instructions for replacing the dispenser actuator on a Frigidaire refrigerator. The most common reason for replacing the actuator is if it is damaged.

All of the information for this refrigerator actuator replacement video is applicable to the following brands:
Arctic Air, Crosley, Electrolux, Frigidaire, Gibson, Kelvinator, Tappan, Westinghouse

Tools needed: multi-screwdriver

Step By Step Instructions

1
Be sure to unplug the power cord.
2
Use a phillips-head screwdriver or a number two square drive bit to unthread the screws securing the dispenser control assembly.
3
Detach the assembly.
4
Note the location of the wire connecters then disconnect them.
5
Now unthread the screws securing the dispenser module.
6
Release the water tube from the retaining clips and the guide holes and remove the module.
7
Use a small flat-head screwdriver to release the actuator mounting tab and you can pull the old actuator free.
8
Install the new dispenser actuator by inserting the mounting tab into the chute assembly until it snaps into place.
9
Reinstall the dispenser module by first inserting the water tube through the guide holes then secure the tube in the retaining clips.
10
Fully position the module then thread and tighten the screws to secure.
11
Reconnect the wires to the appropriate terminals on the dispenser control assembly.
12
Realign the upper edge of the assembly under the door panel position the assembly and secure it with the screws. With the repair completed
13
Plug the power cord back in and your refrigerator should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the dispenser actuator on a Frigidaire refrigerator. The most common reason for replacing the actuator is if it is damaged.

All of the information for this refrigerator actuator replacement video is applicable to the following brands:
Arctic Air, Crosley, Electrolux, Frigidaire, Gibson, Kelvinator, Tappan, Westinghouse

Tools needed: multi-screwdriver
Step-By-Step Instructions
1
Be sure to unplug the power cord.
2
Use a phillips-head screwdriver or a number two square drive bit to unthread the screws securing the dispenser control assembly.
3
Detach the assembly.
4
Note the location of the wire connecters then disconnect them.
5
Now unthread the screws securing the dispenser module.
6
Release the water tube from the retaining clips and the guide holes and remove the module.
7
Use a small flat-head screwdriver to release the actuator mounting tab and you can pull the old actuator free.
8
Install the new dispenser actuator by inserting the mounting tab into the chute assembly until it snaps into place.
9
Reinstall the dispenser module by first inserting the water tube through the guide holes then secure the tube in the retaining clips.
10
Fully position the module then thread and tighten the screws to secure.
11
Reconnect the wires to the appropriate terminals on the dispenser control assembly.
12
Realign the upper edge of the assembly under the door panel position the assembly and secure it with the screws. With the repair completed
13
Plug the power cord back in and your refrigerator should be ready for use.

Applicable Product Model

Refrigerator
Brand
Product Type
Model
Subtype
Cooling System
Icemaking System
Dispensing System
Product Diagram & Manuals
Parts Needed
Total$0.00

Related Articles & Videos

03:53
Part Replacement
Frigidaire Refrigerator Power Cord Replacement #241516901
04:27
Part Replacement
Frigidaire Refrigerator Ice Maker Replacement #5304504052
03:44
Part Replacement
Frigidaire Refrigerator Left Freezer Drawer Slide #5303918726
05:53
Part Replacement
Frigidaire Refrigerator Replace Water Filter Base #807931801
01:14
Part Replacement
Frigidaire Refrigerator Water Filter Replacement #EPTWFU01