Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairWhirlpool Alpha Electric Dryer Drive Motor Replacement #W10806758
Whirlpool Alpha Electric Dryer Drive Motor Replacement #W10806758
Skill Level
Total Parts Cost
$202.48Estimated Savings
$112.5010:48
- Description
This video provides step-by-step repair instructions for replacing the drive motor on a Whirlpool electric dryer (model #WED85HEFW0). The most common reason for replacing the motor is if the drum will not spin.
This motor replacement video is applicable to the following brands:
Whirlpool, Maytag
Tools needed: T-25 Torx bit, Phillips-head screwdriver, 1/4" socket
Don't forget to like and comment on this video and subscribe to our channel!
This motor replacement video is applicable to the following brands:
Whirlpool, Maytag
Tools needed: T-25 Torx bit, Phillips-head screwdriver, 1/4" socket
Don't forget to like and comment on this video and subscribe to our channel!
Step By Step Instructions
1
Anncr: repairclinic makes fixing things easy…
2
…with millions of replacement parts available on our website…
3
…and the help you need to do the repair yourself.
4
Since we encourage you to perform this repair safely, a warning icon will appear when you should use caution.
5
Before you replace the drive motor in your dryer…
6
…be sure to unplug the power cord.
7
Use a quarter-inch socket or nut driver to unthread the rear screws securing the top panel and bracket to the rear panel.
8
Slide the top panel back and lift up to detach.
9
Next, unthread the screws securing the control housing.
10
Disconnect the control panel wire connecter from the control board.
11
You can now lift the control housing and panel up and out to remove.
12
Disconnect the door switch wire harness.
13
Lift up the front of the dryer and support it…
14
Use the quarter-inch socket or nut driver to fully unthread the outer screws securing the bottom of the front panel.
15
Loosen the two middle screws.
16
Remove the support and lower the appliance.
17
Next, open the dryer door and use a phillips-head screwdriver to unthread the two screws securing the front panel to the bulkhead.
18
Use the quarter-inch socket or nut driver to unthread the three top screws.
19
Lift the front panel up and out to remove.
20
Next, unthread the screws securing the control housing bracket.
21
Unthread the screw securing the front of the control board bracket.
22
Use wire or tape to support the bracket.
23
You can now lift the control housing bracket up to remove.
24
Disconnect the moisture sensor wire harness.
25
Unthread the screw to release the lower retaining bracket.
26
Now unthread the four screws securing the front bulkhead to the frame.
27
Lift the bulkhead up and detach it from the drum and frame.
28
Now reach under the drum and…
29
…push the idler pulley to release the tension on the belt then unthread the belt from the pulley and motor shaft.
30
You can use the belt to help lift out the drum.
31
Unthread the mounting screw securing the blower cover and remove the cover.
32
Now use a 7/16th inch wrench to secure the motor shaft and a half-inch square drive socket to loosen the blower wheel by rotating it clockwise.
33
Fully unthread the wheel.
34
Next, disconnect the motor wire harness.
35
Use pliers to remove the front and rear motor retaining clips.
36
You can now lift out the old motor.
37
Install the new drive motor…
38
…by properly aligning it on the mounts.
39
Snap the retaining clips into place.
40
Connect the motor wire harness.
41
Secure the motor shaft then thread the blower wheel counter-clockwise and tighten.
42
Replace the blower cover and secure it with the screw.
43
Replace the drum…
44
…by aligning the smaller rim on the rear rollers.
45
Loop the belt around the pulley and motor shaft in a zig-zag formation.
46
Now, rotate the drum to help align the belt.
47
Reinstall the front bulkhead…
48
…by hooking it onto the frame as you align the rollers under the drum.
49
Rethread and tighten the four screws to secure the bulkhead.
50
Reposition the lower retaining bracket and secure it with the screw.
51
Reconnect the moisture sensor wire harness.
52
Reposition the control housing bracket on the frame under the control board bracket.
53
Replace the screws to secure.
54
Reposition the front panel on the loosened screws…
55
…and feed the wire under the control housing bracket…
56
…then align the top edge of the panel on the mounting tabs.
57
Thread and tighten the top screws.
58
Replace the screws behind the door.
59
Support the dryer…
60
…and tighten the two middle screws securing the bottom of the front panel.
61
Thread and tighten the outer screws.
62
Remove the support.
63
Connect the door switch wire harness.
64
Feed the control panel wire through the housing and control board mounting brackets…
65
…and snap the control housing into place.
66
Thread the screws to secure.
67
Connect the wire connecter to the control board.
68
Realign the top panel and bracket then slide into position.
69
Rethread the rear screws and tighten.
70
With the repair completed…
71
…plug the power cord back in…
72
…and your dryer should be ready for use.
73
At repairclinic – we make fixing things easy.
74
Thank you for supporting the production of these videos by purchasing your parts from our website.
Description
This video provides step-by-step repair instructions for replacing the drive motor on a Whirlpool electric dryer (model #WED85HEFW0). The most common reason for replacing the motor is if the drum will not spin.
This motor replacement video is applicable to the following brands:
Whirlpool, Maytag
Tools needed: T-25 Torx bit, Phillips-head screwdriver, 1/4" socket
Don't forget to like and comment on this video and subscribe to our channel!
This motor replacement video is applicable to the following brands:
Whirlpool, Maytag
Tools needed: T-25 Torx bit, Phillips-head screwdriver, 1/4" socket
Don't forget to like and comment on this video and subscribe to our channel!
Step-By-Step Instructions
1
Anncr: repairclinic makes fixing things easy…
2
…with millions of replacement parts available on our website…
3
…and the help you need to do the repair yourself.
4
Since we encourage you to perform this repair safely, a warning icon will appear when you should use caution.
5
Before you replace the drive motor in your dryer…
6
…be sure to unplug the power cord.
7
Use a quarter-inch socket or nut driver to unthread the rear screws securing the top panel and bracket to the rear panel.
8
Slide the top panel back and lift up to detach.
9
Next, unthread the screws securing the control housing.
10
Disconnect the control panel wire connecter from the control board.
11
You can now lift the control housing and panel up and out to remove.
12
Disconnect the door switch wire harness.
13
Lift up the front of the dryer and support it…
14
Use the quarter-inch socket or nut driver to fully unthread the outer screws securing the bottom of the front panel.
15
Loosen the two middle screws.
16
Remove the support and lower the appliance.
17
Next, open the dryer door and use a phillips-head screwdriver to unthread the two screws securing the front panel to the bulkhead.
18
Use the quarter-inch socket or nut driver to unthread the three top screws.
19
Lift the front panel up and out to remove.
20
Next, unthread the screws securing the control housing bracket.
21
Unthread the screw securing the front of the control board bracket.
22
Use wire or tape to support the bracket.
23
You can now lift the control housing bracket up to remove.
24
Disconnect the moisture sensor wire harness.
25
Unthread the screw to release the lower retaining bracket.
26
Now unthread the four screws securing the front bulkhead to the frame.
27
Lift the bulkhead up and detach it from the drum and frame.
28
Now reach under the drum and…
29
…push the idler pulley to release the tension on the belt then unthread the belt from the pulley and motor shaft.
30
You can use the belt to help lift out the drum.
31
Unthread the mounting screw securing the blower cover and remove the cover.
32
Now use a 7/16th inch wrench to secure the motor shaft and a half-inch square drive socket to loosen the blower wheel by rotating it clockwise.
33
Fully unthread the wheel.
34
Next, disconnect the motor wire harness.
35
Use pliers to remove the front and rear motor retaining clips.
36
You can now lift out the old motor.
37
Install the new drive motor…
38
…by properly aligning it on the mounts.
39
Snap the retaining clips into place.
40
Connect the motor wire harness.
41
Secure the motor shaft then thread the blower wheel counter-clockwise and tighten.
42
Replace the blower cover and secure it with the screw.
43
Replace the drum…
44
…by aligning the smaller rim on the rear rollers.
45
Loop the belt around the pulley and motor shaft in a zig-zag formation.
46
Now, rotate the drum to help align the belt.
47
Reinstall the front bulkhead…
48
…by hooking it onto the frame as you align the rollers under the drum.
49
Rethread and tighten the four screws to secure the bulkhead.
50
Reposition the lower retaining bracket and secure it with the screw.
51
Reconnect the moisture sensor wire harness.
52
Reposition the control housing bracket on the frame under the control board bracket.
53
Replace the screws to secure.
54
Reposition the front panel on the loosened screws…
55
…and feed the wire under the control housing bracket…
56
…then align the top edge of the panel on the mounting tabs.
57
Thread and tighten the top screws.
58
Replace the screws behind the door.
59
Support the dryer…
60
…and tighten the two middle screws securing the bottom of the front panel.
61
Thread and tighten the outer screws.
62
Remove the support.
63
Connect the door switch wire harness.
64
Feed the control panel wire through the housing and control board mounting brackets…
65
…and snap the control housing into place.
66
Thread the screws to secure.
67
Connect the wire connecter to the control board.
68
Realign the top panel and bracket then slide into position.
69
Rethread the rear screws and tighten.
70
With the repair completed…
71
…plug the power cord back in…
72
…and your dryer should be ready for use.
73
At repairclinic – we make fixing things easy.
74
Thank you for supporting the production of these videos by purchasing your parts from our website.
Applicable Product Model
Parts Needed
Drive Motor
$202.48
Total$0.00
Related Articles & Videos
10:42
Part Replacement
Whirlpool Alpha Electric Dryer Heating Element Replacement #WP8544771
09:26
Part Replacement
Whirlpool Alpha Electric Dryer Motor Pulley Replacement #WP8066184
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com