Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairKitchenaid Electric Slide-In Range Door Switch Replacement #WP9757262
Kitchenaid Electric Slide-In Range Door Switch Replacement #WP9757262
Skill Level
Total Parts Cost
$76.78Estimated Savings
$112.5007:47
- Description
This video provides step-by-step instructions for replacing the door switch on a Kitchenaid electric slide-in range (model #KSEB900ESS2). The most common reason for replacing the switch is if the oven light will not work properly.
All of the information in this door switch replacement video is applicable to the following brands: Maytag, Amana, Magic Chef, Whirlpool, Tappan, Estate, Kitchenaide
All of the information in this door switch replacement video is applicable to the following brands: Maytag, Amana, Magic Chef, Whirlpool, Tappan, Estate, Kitchenaide
Step By Step Instructions
1
KitchenAid Electric Slide-In Range - KSEB900ESS2
2
Electric Range Oven Door Switch Replacement
3
Tools needed: Phillips-head screwdriver, flat-head screwdriver
4
Shock
5
Be sure to unplug the power cord or shut off the power supply.
6
Confirm that you can easily access the rear of the range then open the oven door and use a Phillips-head screwdriver to unthread the screws securing the control panel?s lower cover.
7
Sharp
8
Remove the cover.
9
Next, unthread the two screws securing the control panel to the frame.
10
Detach the control panel and support it to avoid straining the wires.
11
Now unthread the front bracket screws securing the main top.
12
Unthread the two screws underneath the rear corners of the top.
13
Heavy
14
Pull the main top back and up to remove then set it aside.
15
Using the Phillips-head screwdriver, unthread the two screws securing the lower rear access panel.
16
Sharp
17
Lift the panel up and out to remove.
18
Unthread the three screws to release the left side stop bracket.
19
Repeat to detach the right side bracket.
20
Now lift the upper rear access panel up to remove.
21
For easier access to the door switch, unthread the two screws securing the element support panel to the right side panel.
22
Unthread the four remaining screws securing the side panel.
23
Sharp
24
Now use a flat-head screwdriver to depress the retaining tab at the rear and you can fully detach the panel.
25
Remove the insulating cover.
26
You can now disconnect the door switch wire connecter.
27
Depress the retaining tabs and push the door switch free of the bracket.
28
Pull the actuator rod out of the hole in the front panel and detach the old switch from the rod.
29
Install the new oven door switch by hooking it onto the actuator rod, then feed the rod through the hole in the front panel and snap the switch into place on the bracket.
30
Connect the wire connecter.
31
Reposition the insulating cover.
32
Reinstall the side panel by aligning the frame tabs with the slots on the front of the panel, then snap the panel into position.
33
Secure it with the screws.
34
Replace the screws securing the element support panel to the side panel.
35
Reinstall the upper rear access panel by hooking it on the tabs.
36
Realign the two stop brackets and thread the screws to hold them in place.
37
Reinstall the lower access panel by inserting the tabs in the slots first.
38
Lower the panel and secure it with the screws.
39
Reposition the main top by sliding the rear edge under the lip of the element support panel, then lower the front edge.
40
Replace all of the screws to secure.
41
Realign the control panel on the front brackets.
42
Secure it with the screws.
43
Replace the lower cover, then thread the screws to secure.
44
Plug the power cord back in or restore the power supply and the electric range should be ready for use.
Description
This video provides step-by-step instructions for replacing the door switch on a Kitchenaid electric slide-in range (model #KSEB900ESS2). The most common reason for replacing the switch is if the oven light will not work properly.
All of the information in this door switch replacement video is applicable to the following brands: Maytag, Amana, Magic Chef, Whirlpool, Tappan, Estate, Kitchenaide
All of the information in this door switch replacement video is applicable to the following brands: Maytag, Amana, Magic Chef, Whirlpool, Tappan, Estate, Kitchenaide
Step-By-Step Instructions
1
KitchenAid Electric Slide-In Range - KSEB900ESS2
2
Electric Range Oven Door Switch Replacement
3
Tools needed: Phillips-head screwdriver, flat-head screwdriver
4
Shock
5
Be sure to unplug the power cord or shut off the power supply.
6
Confirm that you can easily access the rear of the range then open the oven door and use a Phillips-head screwdriver to unthread the screws securing the control panel?s lower cover.
7
Sharp
8
Remove the cover.
9
Next, unthread the two screws securing the control panel to the frame.
10
Detach the control panel and support it to avoid straining the wires.
11
Now unthread the front bracket screws securing the main top.
12
Unthread the two screws underneath the rear corners of the top.
13
Heavy
14
Pull the main top back and up to remove then set it aside.
15
Using the Phillips-head screwdriver, unthread the two screws securing the lower rear access panel.
16
Sharp
17
Lift the panel up and out to remove.
18
Unthread the three screws to release the left side stop bracket.
19
Repeat to detach the right side bracket.
20
Now lift the upper rear access panel up to remove.
21
For easier access to the door switch, unthread the two screws securing the element support panel to the right side panel.
22
Unthread the four remaining screws securing the side panel.
23
Sharp
24
Now use a flat-head screwdriver to depress the retaining tab at the rear and you can fully detach the panel.
25
Remove the insulating cover.
26
You can now disconnect the door switch wire connecter.
27
Depress the retaining tabs and push the door switch free of the bracket.
28
Pull the actuator rod out of the hole in the front panel and detach the old switch from the rod.
29
Install the new oven door switch by hooking it onto the actuator rod, then feed the rod through the hole in the front panel and snap the switch into place on the bracket.
30
Connect the wire connecter.
31
Reposition the insulating cover.
32
Reinstall the side panel by aligning the frame tabs with the slots on the front of the panel, then snap the panel into position.
33
Secure it with the screws.
34
Replace the screws securing the element support panel to the side panel.
35
Reinstall the upper rear access panel by hooking it on the tabs.
36
Realign the two stop brackets and thread the screws to hold them in place.
37
Reinstall the lower access panel by inserting the tabs in the slots first.
38
Lower the panel and secure it with the screws.
39
Reposition the main top by sliding the rear edge under the lip of the element support panel, then lower the front edge.
40
Replace all of the screws to secure.
41
Realign the control panel on the front brackets.
42
Secure it with the screws.
43
Replace the lower cover, then thread the screws to secure.
44
Plug the power cord back in or restore the power supply and the electric range should be ready for use.
Applicable Product Model
Related Articles & Videos
09:45
Part Replacement
KitchenAid Convection Gas Range Door Switch Replacement #WP9757262
04:14
Part Replacement
Kitchenaid Electric Slide-In Range Oven Bake Element Replacement #W10779716
02:11
Part Replacement
Kitchenaid Electric Slide-In Range Left Warming Drawer Rail Replacement #W11131365
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com