Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairKitchenAid Convection Gas Range Temperature Sensor Replacement #W10833885 
KitchenAid Convection Gas Range Temperature Sensor Replacement #W10833885
Skill Level
Total Parts Cost
$105.42Estimated Savings
$112.5006:00
- Description
This video provides step-by-step repair instructions for replacing the temperature sensor on a Kitchenaid Gas Convection Range (model #KSGB900ESS01). The most common reason for replacing the sensor is if the oven does not complete a baking cycle properly.
This sensor replacement video is applicable to the following brands:
Whirlpool, Kitchenaid
Don't forget to like and comment on this video and subscribe to our channel!
This sensor replacement video is applicable to the following brands:
Whirlpool, Kitchenaid
Don't forget to like and comment on this video and subscribe to our channel!
Step By Step Instructions
1
Convection gas range - ksgb900ess1
2
Kitchenaid convection gas range - Temperature Sensor Replacement
3
You will need a phillips-head screwdriver and pliers to complete this repair.
4
Shock
5
Be sure to unplug the power cord or shut off the power supply.
6
If you?re replacing the sensor in the oven, pull the range away from the wall so you can access the rear of the appliance.
7
Using a phillips-head screwdriver, unthread the two screws securing the lower rear access panel.
8
Sharp
9
Lift the panel up and out to remove.
10
Unthread the three screws to release the left side stop bracket.
11
Repeat to detach the right side bracket.
12
Now lift the upper rear access panel up to remove.
13
Depress the tab to disconnect the temperature sensor wire connecter.
14
Unthread the sensor mounting screw and pull out the old sensor.
15
Install the new temperature sensor by inserting it through the hole in the real panel, then replace the mounting screw to secure.
16
Connect the wire connecter.
17
Reinstall the upper rear access panel by hooking it on the tabs.
18
Realign the two stop brackets and thread the screws to hold them in place.
19
Reinstall the lower access panel by inserting the tabs in the slots first.
20
Lower the panel and secure it with the screws.
21
To replace the warming drawer temperature sensor, pull out the drawer and remove the rack.
22
Sharp
23
Next, use pliers to bend the slide rails outward to fully detach the drawer assembly ? this may require some effort.
24
Unthread the mounting screw securing the bake element.
25
Lift the element up and pull it forward to access the wires.
26
Disconnect the wires and fully remove the element.
27
Now unthread the temperature sensor mounting screw to release the sensor from the cover.
28
Next, unthread the screw securing the cover.
29
Rotate the cover counter-clockwise and you can disconnect the sensor wire connecter to fully remove the old component.
30
Install the new sensor by feeding the wire through the hole in the cover.
31
Connect the wire connecter.
32
Reposition the cover and secure it with the screw.
33
Position the sensor on the cover and rethread the mounting screw.
34
Reinstall the bake element by first connecting the wires to the terminals.
35
Align the element bracket tabs in the slots in the base.
36
Replace the mounting screw.
37
Pull out the slide rails.
38
Align the slots in the drawer assembly with the tabs on the slide rails and snap the assembly into position.
39
Plug the power cord back in or restore the power supply.
Description
This video provides step-by-step repair instructions for replacing the temperature sensor on a Kitchenaid Gas Convection Range (model #KSGB900ESS01). The most common reason for replacing the sensor is if the oven does not complete a baking cycle properly.
This sensor replacement video is applicable to the following brands:
Whirlpool, Kitchenaid
Don't forget to like and comment on this video and subscribe to our channel!
This sensor replacement video is applicable to the following brands:
Whirlpool, Kitchenaid
Don't forget to like and comment on this video and subscribe to our channel!
Step-By-Step Instructions
1
Convection gas range - ksgb900ess1
2
Kitchenaid convection gas range - Temperature Sensor Replacement
3
You will need a phillips-head screwdriver and pliers to complete this repair.
4
Shock
5
Be sure to unplug the power cord or shut off the power supply.
6
If you?re replacing the sensor in the oven, pull the range away from the wall so you can access the rear of the appliance.
7
Using a phillips-head screwdriver, unthread the two screws securing the lower rear access panel.
8
Sharp
9
Lift the panel up and out to remove.
10
Unthread the three screws to release the left side stop bracket.
11
Repeat to detach the right side bracket.
12
Now lift the upper rear access panel up to remove.
13
Depress the tab to disconnect the temperature sensor wire connecter.
14
Unthread the sensor mounting screw and pull out the old sensor.
15
Install the new temperature sensor by inserting it through the hole in the real panel, then replace the mounting screw to secure.
16
Connect the wire connecter.
17
Reinstall the upper rear access panel by hooking it on the tabs.
18
Realign the two stop brackets and thread the screws to hold them in place.
19
Reinstall the lower access panel by inserting the tabs in the slots first.
20
Lower the panel and secure it with the screws.
21
To replace the warming drawer temperature sensor, pull out the drawer and remove the rack.
22
Sharp
23
Next, use pliers to bend the slide rails outward to fully detach the drawer assembly ? this may require some effort.
24
Unthread the mounting screw securing the bake element.
25
Lift the element up and pull it forward to access the wires.
26
Disconnect the wires and fully remove the element.
27
Now unthread the temperature sensor mounting screw to release the sensor from the cover.
28
Next, unthread the screw securing the cover.
29
Rotate the cover counter-clockwise and you can disconnect the sensor wire connecter to fully remove the old component.
30
Install the new sensor by feeding the wire through the hole in the cover.
31
Connect the wire connecter.
32
Reposition the cover and secure it with the screw.
33
Position the sensor on the cover and rethread the mounting screw.
34
Reinstall the bake element by first connecting the wires to the terminals.
35
Align the element bracket tabs in the slots in the base.
36
Replace the mounting screw.
37
Pull out the slide rails.
38
Align the slots in the drawer assembly with the tabs on the slide rails and snap the assembly into position.
39
Plug the power cord back in or restore the power supply.
Applicable Product Model
Parts Needed
Temperature Sensor
$105.42
Recommended Tools and Accessories
Cooktop Cleaner
$29.50
Total$0.00
Related Articles & Videos
02:10
Part Replacement
Whirlpool Gas Range Oven Temperature Sensor Replacement #W10833885
02:43
Part Replacement
Kitchenaid Electric Slide-In Range Oven Sensor Replacement #W10833885
09:43
Part Replacement
KitchenAid Convection Gas Range Cooling Fan Assembly Replacement #W11107275
08:32
Part Replacement
KitchenAid Convection Gas Range Main Control Board Replacement #W11100100
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com