Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairKitchenaid Double Oven Gas Range Right Control Panel Support Replacement #W10319111 
Kitchenaid Double Oven Gas Range Right Control Panel Support Replacement #W10319111
Skill Level
Total Parts Cost
$46.32Estimated Savings
$112.5008:03
- Description
This video provides step-by-step instructions for replacing the right control panel support on a Kitchenaid double oven gas range (model #KFGD500ESS04). The most common reason for replacing the support is if the control panel is not secured properly.
All of the information in this supportreplacement video is applicable to the following brands: Maytag, Amana, Magic Chef, Whirlpool, Tappan, Estate, Kitchenaide
All of the information in this supportreplacement video is applicable to the following brands: Maytag, Amana, Magic Chef, Whirlpool, Tappan, Estate, Kitchenaide
Step By Step Instructions
1
Be sure to unplug the power cord or shut off the power supply.
2
Shut off the gas supply as well.
3
Pull the range away from the wall so you can access the rear of the appliance.
4
Lift off both grates.
5
Pull off the five control knobs.
6
Open the upper oven door and use a Phillips head screwdriver to unthread the three lower screws securing the manifold panel.
7
Next, unthread the two upper screws securing the panel.
8
With the screws unthreaded, you can lift off the panel.
9
Use an adjustable wrench to unthread the nut to release the gas supply tube from the manifold.
10
Use the Phillips head screwdriver or a quarter-inch nut driver to unthread the front screws securing the cooktop.
11
Next, unthread the four screws securing the upper rear access panel.
12
Disconnect the wire connector from the control board to fully release the panel.
13
Disconnect the ribbon connector from the board.
14
Unthread the four mounting screws to release the board from the control panel.
15
Now, unthread the screws securing the user interface panel.
16
Pull the panel down to detach.
17
Move the cooktop out of the way.
18
Then, use a short or offset Phillips head screwdriver to unthread the lower screws securing the control panel.
19
Now, unthread the upper screws and you can fully remove the panel.
20
Unthread all six screws securing the control panel support.
21
Use curved needle nose pliers to detach the wire retainer and you can fully remove the old support.
22
Install the new control panel support by positioning it on the frame and bracket.
23
Then, thread and tighten the six screws.
24
Snap the wire retainer into the hole in the support.
25
Realign the control panel on the supports.
26
Then, thread the upper and lower screws to secure.
27
Align the user interface panel and secure it with the screws.
28
Position the control board and thread the mounting screws.
29
Connect the ribbon connector to the board.
30
Reinstall the rear access panel by first connecting the wire connector to the board.
31
Align the panel and secure it with the screws.
32
Fully reposition the cooktop.
33
Thread and tighten the two front screws.
34
Insert the gas supply tube into the manifold and thread the nut.
35
Be careful not to damage the tube by over-tightening the nut.
36
Realign the manifold panel on the support brackets.
37
Thread and tighten the upper and lower screws to secure.
38
Replace the control knobs on the valve stems.
39
Reposition the grates.
40
Turn the gas supply back on.
41
Plug the power cord back in or restore the power supply.
42
And the gas range should be ready for use.
Description
This video provides step-by-step instructions for replacing the right control panel support on a Kitchenaid double oven gas range (model #KFGD500ESS04). The most common reason for replacing the support is if the control panel is not secured properly.
All of the information in this supportreplacement video is applicable to the following brands: Maytag, Amana, Magic Chef, Whirlpool, Tappan, Estate, Kitchenaide
All of the information in this supportreplacement video is applicable to the following brands: Maytag, Amana, Magic Chef, Whirlpool, Tappan, Estate, Kitchenaide
Step-By-Step Instructions
1
Be sure to unplug the power cord or shut off the power supply.
2
Shut off the gas supply as well.
3
Pull the range away from the wall so you can access the rear of the appliance.
4
Lift off both grates.
5
Pull off the five control knobs.
6
Open the upper oven door and use a Phillips head screwdriver to unthread the three lower screws securing the manifold panel.
7
Next, unthread the two upper screws securing the panel.
8
With the screws unthreaded, you can lift off the panel.
9
Use an adjustable wrench to unthread the nut to release the gas supply tube from the manifold.
10
Use the Phillips head screwdriver or a quarter-inch nut driver to unthread the front screws securing the cooktop.
11
Next, unthread the four screws securing the upper rear access panel.
12
Disconnect the wire connector from the control board to fully release the panel.
13
Disconnect the ribbon connector from the board.
14
Unthread the four mounting screws to release the board from the control panel.
15
Now, unthread the screws securing the user interface panel.
16
Pull the panel down to detach.
17
Move the cooktop out of the way.
18
Then, use a short or offset Phillips head screwdriver to unthread the lower screws securing the control panel.
19
Now, unthread the upper screws and you can fully remove the panel.
20
Unthread all six screws securing the control panel support.
21
Use curved needle nose pliers to detach the wire retainer and you can fully remove the old support.
22
Install the new control panel support by positioning it on the frame and bracket.
23
Then, thread and tighten the six screws.
24
Snap the wire retainer into the hole in the support.
25
Realign the control panel on the supports.
26
Then, thread the upper and lower screws to secure.
27
Align the user interface panel and secure it with the screws.
28
Position the control board and thread the mounting screws.
29
Connect the ribbon connector to the board.
30
Reinstall the rear access panel by first connecting the wire connector to the board.
31
Align the panel and secure it with the screws.
32
Fully reposition the cooktop.
33
Thread and tighten the two front screws.
34
Insert the gas supply tube into the manifold and thread the nut.
35
Be careful not to damage the tube by over-tightening the nut.
36
Realign the manifold panel on the support brackets.
37
Thread and tighten the upper and lower screws to secure.
38
Replace the control knobs on the valve stems.
39
Reposition the grates.
40
Turn the gas supply back on.
41
Plug the power cord back in or restore the power supply.
42
And the gas range should be ready for use.
Applicable Product Model
Related Articles & Videos
07:46
Part Replacement
Kitchenaid Double Oven Gas Range Bake Burner Tube Igniter Replacement #WP7432P143-60
05:37
Part Replacement
Kitchenaid Double Oven Gas Range Left Front Burner Valve Replacement #W10718180
01:31
Part Replacement
Kitchenaid Double Oven Gas Range Left Front Burner Base Replacement #WPW10406878
04:10
Part Replacement
Kitchenaid Double Oven Gas Range Broil Igniter Replacement #WPW10324738
06:05
Part Replacement
Kitchenaid Double Oven Gas Range Surface Igniter Replacement #W11208293
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com