Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairWhirlpool Electric Washer/Dryer Combo Heating Element Replacement #WP3387749 
Whirlpool Electric Washer/Dryer Combo Heating Element Replacement #WP3387749
Skill Level
Total Parts Cost
$153.95Estimated Savings
$112.5003:57
- Description
This video provides step-by-step repair instructions for replacing the heating element on a Whirlpool electric washer/dryer combo (model #WET4027EW0). The most common reason for replacing this part is if the dryer will not heat.
This replacement video is applicable to the following brands:
Whirlpool, Maytag, Kitchenaid
Don't forget to like and comment on this video and subscribe to our channel!
This replacement video is applicable to the following brands:
Whirlpool, Maytag, Kitchenaid
Don't forget to like and comment on this video and subscribe to our channel!
Step By Step Instructions
1
Before you replace the heating element in your washer / dryer combo…
2
…be sure to unplug the power cord or shut off the power supply.
3
Use a phillips-head screwdriver to unthread the screws securing the lower access panel.
4
Detach the panel and set it aside.
5
Insert a putty knife above the front access panel to release the spring clips to detach the panel.
6
Remove the lint screen.
7
Next, use a 5/16th inch socket or nut driver to unthread the screws to release the air duct.
8
Unthread the four screws securing the heater shield.
9
Detach the shield.
10
Disconnect the heating element wires.
11
Use a quarter-inch socket or nut driver to unthread the left side screw securing the heating element to the housing.
12
With the screw unthreaded, you can slide the old element out.
13
Install the new heating element…
14
…by sliding it into the housing.
15
Thread the left side screw to secure.
16
Connect the wires to the element terminals.
17
Reposition the heater shield and secure it with the four screws.
18
Realign the air duct and thread the screws to secure.
19
Replace the lint screen.
20
Align the front access panel spring clips with the slots and snap the panel into place.
21
Reposition the lower access panel and secure it with the screws.
22
Plug the power cord back in or restore the power supply…
23
…and your washer/dryer combo should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the heating element on a Whirlpool electric washer/dryer combo (model #WET4027EW0). The most common reason for replacing this part is if the dryer will not heat.
This replacement video is applicable to the following brands:
Whirlpool, Maytag, Kitchenaid
Don't forget to like and comment on this video and subscribe to our channel!
This replacement video is applicable to the following brands:
Whirlpool, Maytag, Kitchenaid
Don't forget to like and comment on this video and subscribe to our channel!
Step-By-Step Instructions
1
Before you replace the heating element in your washer / dryer combo…
2
…be sure to unplug the power cord or shut off the power supply.
3
Use a phillips-head screwdriver to unthread the screws securing the lower access panel.
4
Detach the panel and set it aside.
5
Insert a putty knife above the front access panel to release the spring clips to detach the panel.
6
Remove the lint screen.
7
Next, use a 5/16th inch socket or nut driver to unthread the screws to release the air duct.
8
Unthread the four screws securing the heater shield.
9
Detach the shield.
10
Disconnect the heating element wires.
11
Use a quarter-inch socket or nut driver to unthread the left side screw securing the heating element to the housing.
12
With the screw unthreaded, you can slide the old element out.
13
Install the new heating element…
14
…by sliding it into the housing.
15
Thread the left side screw to secure.
16
Connect the wires to the element terminals.
17
Reposition the heater shield and secure it with the four screws.
18
Realign the air duct and thread the screws to secure.
19
Replace the lint screen.
20
Align the front access panel spring clips with the slots and snap the panel into place.
21
Reposition the lower access panel and secure it with the screws.
22
Plug the power cord back in or restore the power supply…
23
…and your washer/dryer combo should be ready for use.
Applicable Product Model
Parts Needed
Heating Element
$153.95
Total$0.00
Related Articles & Videos
07:29
How This Part Works
Electric Dryer Heating Element - How it Works & Installation Tips
05:07
Part Replacement
Whirlpool Electric Washer/Dryer Combo Lid Switch Assembly Replacement Part # WP3355458
08:48
Part Replacement
Whirlpool Electric Washer/Dryer Combo Dryer Drive Belt Replacement #661570V
04:26
Part Replacement
Whirlpool Electric Washer/Dryer Combo Heating Element Thermal Fuse Replacement #279769
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com