Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairWhirlpool Gas Range Convection Fan Motor Replacement #W11043837 
Whirlpool Gas Range Convection Fan Motor Replacement #W11043837
Skill Level
Total Parts Cost
$236.94Estimated Savings
$112.5002:54
- Description
This video provides step-by-step repair instructions for replacing the convection fan motor on a Whirlpool gas range. The most common reason for replacing this part is if the convection function will not work properly, or if there is a loud noise coming from the oven.
All of the information for this part replacement video is applicable to the following brands:
Whirlpool
All of the information for this part replacement video is applicable to the following brands:
Whirlpool
Step By Step Instructions
1
Whirlpool Gas Range - WFG745H0FS1
2
Gas Range Convection Fan Motor Assembly Replacement
3
Tools needed: Phillips-head screwdriver
4
Shock Hazard
5
Be sure to unplug the power cord or shut off the power supply.
6
Fully open the oven door and rotate both door hinge locks back.
7
Heavy
8
Partially close the door, then lift and pull the door toward you to remove.
9
With the handle side down, set the door on a blanket or towel.
10
Remove the oven racks.
11
Note the orientation of the fan cover, then use a Phillips-head screwdriver to unthread the screws to release the cover.
12
Sharp
13
Turn the fan motor assembly around ? note the orientation of the wires connected to the convection element ? then disconnect them.
14
Disconnect the wire connecter to fully remove the old assembly ? make sure the wires don?t slip behind the rear panel.
15
Install the new convection fan motor assembly by first connecting the wire connecter.
16
Attach the wires to the convection element terminals?then position the assembly on the rear of the oven.
17
Properly reposition the fan cover then thread and tighten the screws to secure.
18
Replace the oven racks.
19
Reinstall the oven door by inserting the door hinges into the hinge slots at a forty-five degree angle.
20
Lower the door to its fully open position, then rotate the hinge locks forward.
21
Plug the power cord back in or restore the power supply and the gas range should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the convection fan motor on a Whirlpool gas range. The most common reason for replacing this part is if the convection function will not work properly, or if there is a loud noise coming from the oven.
All of the information for this part replacement video is applicable to the following brands:
Whirlpool
All of the information for this part replacement video is applicable to the following brands:
Whirlpool
Step-By-Step Instructions
1
Whirlpool Gas Range - WFG745H0FS1
2
Gas Range Convection Fan Motor Assembly Replacement
3
Tools needed: Phillips-head screwdriver
4
Shock Hazard
5
Be sure to unplug the power cord or shut off the power supply.
6
Fully open the oven door and rotate both door hinge locks back.
7
Heavy
8
Partially close the door, then lift and pull the door toward you to remove.
9
With the handle side down, set the door on a blanket or towel.
10
Remove the oven racks.
11
Note the orientation of the fan cover, then use a Phillips-head screwdriver to unthread the screws to release the cover.
12
Sharp
13
Turn the fan motor assembly around ? note the orientation of the wires connected to the convection element ? then disconnect them.
14
Disconnect the wire connecter to fully remove the old assembly ? make sure the wires don?t slip behind the rear panel.
15
Install the new convection fan motor assembly by first connecting the wire connecter.
16
Attach the wires to the convection element terminals?then position the assembly on the rear of the oven.
17
Properly reposition the fan cover then thread and tighten the screws to secure.
18
Replace the oven racks.
19
Reinstall the oven door by inserting the door hinges into the hinge slots at a forty-five degree angle.
20
Lower the door to its fully open position, then rotate the hinge locks forward.
21
Plug the power cord back in or restore the power supply and the gas range should be ready for use.
Applicable Product Model
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com