Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairWhirlpool Gas Range Touchpad Membrane Overlay Replacement #W10881756 
Whirlpool Gas Range Touchpad Membrane Overlay Replacement #W10881756
Skill Level
Total Parts Cost
$185.29Estimated Savings
$112.5004:14
- Description
This video provides step-by-step repair instructions for replacing the touchpad membrane overlay on a Whirlpool gas range. The most common reason for replacing this part is if the broiler will not light.
All of the information for this part replacement video is applicable to the following brands:
Whirlpool
All of the information for this part replacement video is applicable to the following brands:
Whirlpool
Step By Step Instructions
1
Whirlpool Gas Range - WFG745H0FS1
2
Gas Range Membrane Overlay Assembly Replacement
3
Tools needed: short Phillips-head screwdriver
4
Shock Hazard
5
Be sure to unplug the power cord or shut off the power supply.
6
Pull the range away from the wall so you can access the rear of the appliance.
7
Use the Phillips-head screwdriver or a number two square drive bit to unthread the screws securing the lower rear access panel.
8
Sharp
9
Lift the panel up and out.
10
Now unthread the screws to release the upper rear access panel.
11
Pull the panel down to remove.
12
Disconnect the ribbon connecter from the main control board.
13
Unthread the mounting screws to release the board from the support brackets.
14
Unthread the spark module board mounting screw, then lift the board up to detach.
15
Use a short Phillips-head screwdriver to unthread the lower screws securing the control panel frame to the supports.
16
You can now fully detach the frame.
17
Sharp
18
Depress the upper tabs to release the spark module board mounting plate.
19
Next, pull out the bottom edge of the frame to detach the tabs?then remove the old overlay assembly.
20
Install the new membrane overlay assembly by aligning it in the control panel frame and snapping it into place.
21
Realign the spark module board mounting plate and snap it into place on the frame.
22
Now reposition the frame on the supports.
23
Thread and tighten the lower screws.
24
Align the spark module board mounting posts in the slots, then thread the mounting screw.
25
Reposition the main control board and secure it with the screws.
26
Connect the new ribbon connecter to the board.
27
Reinstall the upper rear access panel and secure it with the screws.
28
Reinstall the lower rear access panel.
29
Thread the screws.
30
Plug the power cord back in or restore the power supply and the gas range should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the touchpad membrane overlay on a Whirlpool gas range. The most common reason for replacing this part is if the broiler will not light.
All of the information for this part replacement video is applicable to the following brands:
Whirlpool
All of the information for this part replacement video is applicable to the following brands:
Whirlpool
Step-By-Step Instructions
1
Whirlpool Gas Range - WFG745H0FS1
2
Gas Range Membrane Overlay Assembly Replacement
3
Tools needed: short Phillips-head screwdriver
4
Shock Hazard
5
Be sure to unplug the power cord or shut off the power supply.
6
Pull the range away from the wall so you can access the rear of the appliance.
7
Use the Phillips-head screwdriver or a number two square drive bit to unthread the screws securing the lower rear access panel.
8
Sharp
9
Lift the panel up and out.
10
Now unthread the screws to release the upper rear access panel.
11
Pull the panel down to remove.
12
Disconnect the ribbon connecter from the main control board.
13
Unthread the mounting screws to release the board from the support brackets.
14
Unthread the spark module board mounting screw, then lift the board up to detach.
15
Use a short Phillips-head screwdriver to unthread the lower screws securing the control panel frame to the supports.
16
You can now fully detach the frame.
17
Sharp
18
Depress the upper tabs to release the spark module board mounting plate.
19
Next, pull out the bottom edge of the frame to detach the tabs?then remove the old overlay assembly.
20
Install the new membrane overlay assembly by aligning it in the control panel frame and snapping it into place.
21
Realign the spark module board mounting plate and snap it into place on the frame.
22
Now reposition the frame on the supports.
23
Thread and tighten the lower screws.
24
Align the spark module board mounting posts in the slots, then thread the mounting screw.
25
Reposition the main control board and secure it with the screws.
26
Connect the new ribbon connecter to the board.
27
Reinstall the upper rear access panel and secure it with the screws.
28
Reinstall the lower rear access panel.
29
Thread the screws.
30
Plug the power cord back in or restore the power supply and the gas range should be ready for use.
Applicable Product Model
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com