Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairWhirlpool Gas Range Power Cord Replacement #W11023766 
Whirlpool Gas Range Power Cord Replacement #W11023766
Skill Level
Total Parts Cost
$10.28Estimated Savings
$112.5007:41
- Description
This video provides step-by-step repair instructions for replacing the power cord on a Whirlpool gas range. The most common reason for replacing this part is if the range will not power on.
All of the information for this part replacement video is applicable to the following brands:
Whirlpool
All of the information for this part replacement video is applicable to the following brands:
Whirlpool
Step By Step Instructions
1
Whirlpool Gas Range - WFG745H0FS1
2
Gas Range Power Cord Replacement
3
Tools needed: Phillips-head screwdriver, flat-head screwdriver
4
Shock Hazard
5
Be sure to unplug the old power cord.
6
Fire Hazard
7
Shut off the gas supply as well.
8
Pull the range away from the wall so you can access the rear of the appliance.
9
Heavy
10
Carefully lift off the two grates.
11
Remove the burner caps from the left and right side burner bases.
12
Lift the center burner base straight up to remove.
13
Use a Phillips-head screwdriver to unthread the two screws securing the center orifice holder to the main cooktop.
14
Next, unthread the screws securing the four remaining burner bases to the cooktop.
15
Lift the bases up and depress the tabs to release the spark electrode wires from each base ? make sure the wires don?t slip below the cooktop.
16
Pull off all five control knobs.
17
Now open the oven door and use the Phillips-head screwdriver to unthread the two mounting screws securing the front control panel.
18
Sharp
19
Lift the panel up and out.
20
Unthread the two screws securing the main cooktop to the support bracket.
21
Heavy
22
Lift up the cooktop and unthread the screw to release the spark module bracket.
23
Fully remove the cooktop.
24
Next, use the Phillips-head screwdriver or a number two square drive bit to unthread the screws securing the lower rear access panel.
25
Sharp
26
Lift the panel up and out.
27
Now unthread the six screws to detach the right side panel.
28
Disconnect the power cord wire connecter.
29
Use a flat-head screwdriver to help depress the retaining tabs to release the power cord strain relief.
30
Unthread the grounding wire screw and you can fully remove the old cord.
31
Install the new power cord by feeding the wire through the rear panel then snap the strain relief into place.
32
Secure the grounding wire with the screw.
33
Connect the wire connecter.
34
Reposition the side panel.
35
Thread and tighten the screws to secure.
36
Reinstall the lower rear access panel.
37
Thread the screws to hold it in place.
38
Reinstall the cooktop by aligning the spark module bracket and securing it with the screw.
39
Fully position the top making sure the orifice holders protrude through the holes in the top and the spark electrode wires are accessible.
40
Thread the two lower screws to secure the cooktop.
41
Reinstall the front control panel by aligning the slots in the panel on the mounting bracket tabs.
42
Thread the mounting screws to secure.
43
Realign the control knobs on the valve stems.
44
Replace the screws to secure the center orifice holder to the top.
45
Reposition the center burner base on the orifice holder so the spark electrode aligns with the notch in the base.
46
Reinstall the remaining burner bases by first connecting the spark electrode wires, then position the bases and thread the screws to hold them in place.
47
Realign the burner caps.
48
Replace the grates by positioning them on the supports and gently lowering them.
49
Turn the gas supply back on, plug the new power cord in and the gas range should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the power cord on a Whirlpool gas range. The most common reason for replacing this part is if the range will not power on.
All of the information for this part replacement video is applicable to the following brands:
Whirlpool
All of the information for this part replacement video is applicable to the following brands:
Whirlpool
Step-By-Step Instructions
1
Whirlpool Gas Range - WFG745H0FS1
2
Gas Range Power Cord Replacement
3
Tools needed: Phillips-head screwdriver, flat-head screwdriver
4
Shock Hazard
5
Be sure to unplug the old power cord.
6
Fire Hazard
7
Shut off the gas supply as well.
8
Pull the range away from the wall so you can access the rear of the appliance.
9
Heavy
10
Carefully lift off the two grates.
11
Remove the burner caps from the left and right side burner bases.
12
Lift the center burner base straight up to remove.
13
Use a Phillips-head screwdriver to unthread the two screws securing the center orifice holder to the main cooktop.
14
Next, unthread the screws securing the four remaining burner bases to the cooktop.
15
Lift the bases up and depress the tabs to release the spark electrode wires from each base ? make sure the wires don?t slip below the cooktop.
16
Pull off all five control knobs.
17
Now open the oven door and use the Phillips-head screwdriver to unthread the two mounting screws securing the front control panel.
18
Sharp
19
Lift the panel up and out.
20
Unthread the two screws securing the main cooktop to the support bracket.
21
Heavy
22
Lift up the cooktop and unthread the screw to release the spark module bracket.
23
Fully remove the cooktop.
24
Next, use the Phillips-head screwdriver or a number two square drive bit to unthread the screws securing the lower rear access panel.
25
Sharp
26
Lift the panel up and out.
27
Now unthread the six screws to detach the right side panel.
28
Disconnect the power cord wire connecter.
29
Use a flat-head screwdriver to help depress the retaining tabs to release the power cord strain relief.
30
Unthread the grounding wire screw and you can fully remove the old cord.
31
Install the new power cord by feeding the wire through the rear panel then snap the strain relief into place.
32
Secure the grounding wire with the screw.
33
Connect the wire connecter.
34
Reposition the side panel.
35
Thread and tighten the screws to secure.
36
Reinstall the lower rear access panel.
37
Thread the screws to hold it in place.
38
Reinstall the cooktop by aligning the spark module bracket and securing it with the screw.
39
Fully position the top making sure the orifice holders protrude through the holes in the top and the spark electrode wires are accessible.
40
Thread the two lower screws to secure the cooktop.
41
Reinstall the front control panel by aligning the slots in the panel on the mounting bracket tabs.
42
Thread the mounting screws to secure.
43
Realign the control knobs on the valve stems.
44
Replace the screws to secure the center orifice holder to the top.
45
Reposition the center burner base on the orifice holder so the spark electrode aligns with the notch in the base.
46
Reinstall the remaining burner bases by first connecting the spark electrode wires, then position the bases and thread the screws to hold them in place.
47
Realign the burner caps.
48
Replace the grates by positioning them on the supports and gently lowering them.
49
Turn the gas supply back on, plug the new power cord in and the gas range should be ready for use.
Applicable Product Model
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com