Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairWhirlpool Gas Range Broil Orifice Assembly Replacement #W10776437 
Whirlpool Gas Range Broil Orifice Assembly Replacement #W10776437
Skill Level
Total Parts Cost
$68.68Estimated Savings
$112.5004:29
- Description
This video provides step-by-step repair instructions for replacing the broil orifice assembly on a Whirlpool gas range. The most common reason for replacing this part is if the broiler will not light.
All of the information for this part replacement video is applicable to the following brands:
Whirlpool
All of the information for this part replacement video is applicable to the following brands:
Whirlpool
Step By Step Instructions
1
Whirlpool Gas Range - WFG745H0FS1
2
Gas Range Broil Orifice Assembly Replacement
3
Tools needed: Phillips-head screwdriver or a number two square drive bit, 9/16th inch wrench, 5/8th inch wrench
4
Shock Hazard
5
Be sure to unplug the power cord or shut off the power supply.
6
Fire Hazard
7
Shut off the gas supply as well.
8
Pull the range away from the wall so you can access the rear of the appliance.
9
Fully open the oven door and rotate both door hinge locks back.
10
Heavy
11
Partially close the door, then lift and pull the door toward you to remove.
12
With the handle side down, set the door on a blanket or towel.
13
Remove the oven racks.
14
Use a Phillips-head screwdriver or a number two square drive bit to unthread the broil burner tube mounting screw.
15
Sharp
16
Remove the shield.
17
Detach the burner tube and disconnect the spark electrode wire to fully remove the burner tube ? be careful not to let the electrode wire slip behind the back panel.
18
Next, unthread the screws securing the lower rear access panel.
19
Sharp
20
Lift the panel up and out.
21
Use a 9/16th inch wrench and a 5/8th inch wrench to unthread the nut to release the gas supply tube from the broil orifice fitting.
22
Now use a Phillips-head screwdriver to unthread the two mounting screws securing the broil orifice fitting.
23
Remove the old assembly.
24
You?re now ready to install the new broil orifice assembly.
25
Be aware, if your range uses liquid propane, you will need to transfer the orifice from the old fitting to the new one.
26
Insert the fitting through the rear of the oven, then thread and tighten the mounting screws to secure.
27
Insert the gas supply tube into the new fitting then thread the nut ? be careful not to damage the tube by overtightening the nut.
28
Reinstall the lower rear access panel.
29
Thread the screws to secure.
30
Reinstall the broil burner tube by first connecting the wire to the spark electrode.
31
Position the burner tube over the orifice.
32
Realign the shield, then fully position the assembly and thread the front mounting screw.
33
Replace the oven racks.
34
Reinstall the oven door by inserting the door hinges into the hinge slots at a forty-five degree angle.
35
Lower the door to its fully open position, then rotate the hinge locks forward.
36
Turn the gas supply back on, plug the power cord back in or restore the power supply and the gas range should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the broil orifice assembly on a Whirlpool gas range. The most common reason for replacing this part is if the broiler will not light.
All of the information for this part replacement video is applicable to the following brands:
Whirlpool
All of the information for this part replacement video is applicable to the following brands:
Whirlpool
Step-By-Step Instructions
1
Whirlpool Gas Range - WFG745H0FS1
2
Gas Range Broil Orifice Assembly Replacement
3
Tools needed: Phillips-head screwdriver or a number two square drive bit, 9/16th inch wrench, 5/8th inch wrench
4
Shock Hazard
5
Be sure to unplug the power cord or shut off the power supply.
6
Fire Hazard
7
Shut off the gas supply as well.
8
Pull the range away from the wall so you can access the rear of the appliance.
9
Fully open the oven door and rotate both door hinge locks back.
10
Heavy
11
Partially close the door, then lift and pull the door toward you to remove.
12
With the handle side down, set the door on a blanket or towel.
13
Remove the oven racks.
14
Use a Phillips-head screwdriver or a number two square drive bit to unthread the broil burner tube mounting screw.
15
Sharp
16
Remove the shield.
17
Detach the burner tube and disconnect the spark electrode wire to fully remove the burner tube ? be careful not to let the electrode wire slip behind the back panel.
18
Next, unthread the screws securing the lower rear access panel.
19
Sharp
20
Lift the panel up and out.
21
Use a 9/16th inch wrench and a 5/8th inch wrench to unthread the nut to release the gas supply tube from the broil orifice fitting.
22
Now use a Phillips-head screwdriver to unthread the two mounting screws securing the broil orifice fitting.
23
Remove the old assembly.
24
You?re now ready to install the new broil orifice assembly.
25
Be aware, if your range uses liquid propane, you will need to transfer the orifice from the old fitting to the new one.
26
Insert the fitting through the rear of the oven, then thread and tighten the mounting screws to secure.
27
Insert the gas supply tube into the new fitting then thread the nut ? be careful not to damage the tube by overtightening the nut.
28
Reinstall the lower rear access panel.
29
Thread the screws to secure.
30
Reinstall the broil burner tube by first connecting the wire to the spark electrode.
31
Position the burner tube over the orifice.
32
Realign the shield, then fully position the assembly and thread the front mounting screw.
33
Replace the oven racks.
34
Reinstall the oven door by inserting the door hinges into the hinge slots at a forty-five degree angle.
35
Lower the door to its fully open position, then rotate the hinge locks forward.
36
Turn the gas supply back on, plug the power cord back in or restore the power supply and the gas range should be ready for use.
Applicable Product Model
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com