Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairElectrolux Dishwasher Internal Light Assembly Replacement 5304521592 
Electrolux Dishwasher Internal Light Assembly Replacement 5304521592
Skill Level
Total Parts Cost
$103.02Estimated Savings
$112.5005:20
- Description
This video provides step-by-step instructions for replacing the internal light assembly on Electrolux dishwashers.
All of the information in this video is applicable to the following brands: Electrolux
All of the information in this video is applicable to the following brands: Electrolux
Step By Step Instructions
1
To replace the internal light assembly in your dishwasher,
2
You will need to fully uninstall the appliance before you attempt this.
3
Be sure to turn off the power to the dishwasher and shut off the water supply valve.
4
Using a Phillips head screwdriver, unthread the two mounting screws securing the lower access panel.
5
Set the panel aside.
6
Use channel lock pliers to loosen the elbow fitting securing the water supply line to the inlet valve.
7
Fully unthread the elbow fitting.
8
Be prepared for some water to spill.
9
Next, disconnect the drain hose from the sink drain or garbage disposer and feed it through the cabinet.
10
Open the dishwasher door and unthread the two screws securing the dishwasher mounting brackets to the cabinet or countertop.
11
To move the dishwasher, you may need to adjust the legs.
12
To lower the appliance, rotate the front legs clockwise.
13
Using the Philips head screwdriver, rotate the rear leg adjusting rod counterclockwise to lower the rear of the dishwasher.
14
Now, gently pull the dishwasher away from the cabinet.
15
Place a weight on top of the dishwasher to help stabilize it.
16
Pull the upper dish rack out and rotate both front stop clips outward to fully remove the rack.
17
Lift up the right-side insulation, then reach into the dishwasher to hold the light lens in place as you rotate the light assembly counterclockwise to detach.
18
Disconnect the wire connector to fully release the old assembly.
19
Prepare the new internal light assembly for installation by detaching the cover.
20
Connect the wire connector to the new light and secure the wire in the retaining clip.
21
Insert the cover into the side panel from the inside, then align the light housing with the cover and rotate clockwise to lock it into place.
22
Reposition the insulation.
23
Realign the upper dish rack rollers on the side rails.
24
Push the rack in and rotate the front's top clips inward.
25
Remove the weight.
26
Confirm that the end of the drain hose is accessible through the cabinet wall, then gently slide the dishwasher back into the cabinet.
27
Extend the front leveling legs if necessary.
28
Rotate the adjusting rod clockwise to extend the rear leg.
29
Rethread the screws to secure the mounting brackets to the cabinet or countertop.
30
Feed the drain hose through the cabinet and connect it to the sink drain or garbage disposer.
31
Make sure the hose is elevated above the connection point.
32
Thread the water supply line elbow fitting onto the inlet valve port and tighten.
33
Realign the lower access panel and rethread the screws to secure.
34
Turn the water supply back on, as well as the power, and your dishwasher should be ready for use.
Description
This video provides step-by-step instructions for replacing the internal light assembly on Electrolux dishwashers.
All of the information in this video is applicable to the following brands: Electrolux
All of the information in this video is applicable to the following brands: Electrolux
Step-By-Step Instructions
1
To replace the internal light assembly in your dishwasher,
2
You will need to fully uninstall the appliance before you attempt this.
3
Be sure to turn off the power to the dishwasher and shut off the water supply valve.
4
Using a Phillips head screwdriver, unthread the two mounting screws securing the lower access panel.
5
Set the panel aside.
6
Use channel lock pliers to loosen the elbow fitting securing the water supply line to the inlet valve.
7
Fully unthread the elbow fitting.
8
Be prepared for some water to spill.
9
Next, disconnect the drain hose from the sink drain or garbage disposer and feed it through the cabinet.
10
Open the dishwasher door and unthread the two screws securing the dishwasher mounting brackets to the cabinet or countertop.
11
To move the dishwasher, you may need to adjust the legs.
12
To lower the appliance, rotate the front legs clockwise.
13
Using the Philips head screwdriver, rotate the rear leg adjusting rod counterclockwise to lower the rear of the dishwasher.
14
Now, gently pull the dishwasher away from the cabinet.
15
Place a weight on top of the dishwasher to help stabilize it.
16
Pull the upper dish rack out and rotate both front stop clips outward to fully remove the rack.
17
Lift up the right-side insulation, then reach into the dishwasher to hold the light lens in place as you rotate the light assembly counterclockwise to detach.
18
Disconnect the wire connector to fully release the old assembly.
19
Prepare the new internal light assembly for installation by detaching the cover.
20
Connect the wire connector to the new light and secure the wire in the retaining clip.
21
Insert the cover into the side panel from the inside, then align the light housing with the cover and rotate clockwise to lock it into place.
22
Reposition the insulation.
23
Realign the upper dish rack rollers on the side rails.
24
Push the rack in and rotate the front's top clips inward.
25
Remove the weight.
26
Confirm that the end of the drain hose is accessible through the cabinet wall, then gently slide the dishwasher back into the cabinet.
27
Extend the front leveling legs if necessary.
28
Rotate the adjusting rod clockwise to extend the rear leg.
29
Rethread the screws to secure the mounting brackets to the cabinet or countertop.
30
Feed the drain hose through the cabinet and connect it to the sink drain or garbage disposer.
31
Make sure the hose is elevated above the connection point.
32
Thread the water supply line elbow fitting onto the inlet valve port and tighten.
33
Realign the lower access panel and rethread the screws to secure.
34
Turn the water supply back on, as well as the power, and your dishwasher should be ready for use.
Applicable Product Model
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com