Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairElectrolux Dishwasher Drain Hose Replacement 807032601 
Electrolux Dishwasher Drain Hose Replacement 807032601
Skill Level
Total Parts Cost
$55.60Estimated Savings
$112.5007:51
- Description
This video provides step-by-step instructions for replacing the drain hose on Electrolux dishwashers.
All of the information in this video is applicable to the following brands: Electrolux
All of the information in this video is applicable to the following brands: Electrolux
Step By Step Instructions
1
Electrolux Dishwasher - 24ID75SPS3A
2
Dishwasher Drain Hose Replacement
3
2, 1, 3",You will need to fully uninstall the appliance
4
3",Turn off the power and water supply to the appliance
5
"Using a phillips-head screwdriver, unthread the two mounting screws securing the lower access panel"
6
Set the panel aside
7
Use channel-lock pliers to loosen the elbow fitting securing the water supply line to the inlet valve
8
Fully unthread the elbow fitting--be prepared for spilled water
9
Disconnect the drain hose from the sink or garbage disposer and feed it through the cabinet
10
Open the dishwasher door and unthread the two screws securing the dishwasher mounting brackets
11
"To move the dishwasher, you may need to adjust the legs to lower the appliance. Rotate the front legs clockwise to lower the front"
12
"Using the phillips-head screwdriver, rotate the rear leg adjusting rod counter-clockwise to lower the rear"
13
Gently pull the dishwasher away from the cabinet
14
"To tip the dishwasher back, you will probably need to detach the power supply cord from the junction box"
15
"Note the orientation of the power wires and grounding wire, then untwist the wire nuts to disconnect the wires"
16
Have an assistant help you to lift up the front of the appliance and support it
17
Unthread the strain relief nut and detach the strain relief and cord from the junction box
18
Remove the support
19
Tip the appliance back and rest it on the rear panel
20
Release the tab to detach the rear leg adjusting rod
21
"Using pliers, squeeze the retaining clips to release the bottom panel"
22
Depress the tabs to release the drain hose collar from the base
23
Use pliers to release the spring clamp securing the drain hose to the sump and pull the hose off the sump
24
Remove the old hose by pulling it through the base
25
Install the new drain hose by feeding the straight end through the hole in the base
26
Slide a spring clamp over the curved end
27
Attach that end to the sump port and secure it with the clamp
28
Feed the drain hose through the cabinet and connect it to the sink drain or disposer
29
Snap the drain hose collar into the base
30
Align the bottom panel tabs with the slots in the base and snap the panel in place
31
Insert the bottom of the adjusting rod into the hole in the base and snap the upper portion in place
32
Return the dishwasher to its upright position
33
"Fully position the power supply cord and strain relief in the junction box, then thread and tighten the nut"
34
Remove the support
35
"Join the black wires together, the white wires together, and the green wires together, securing them with wire nuts"
36
"With the wires repositioned inside the junction box, realign the cover and rethread the screw"
37
Confirm that the water supply line is positioned in the channel in the base then gently slide the dishwasher back into the cabinet
38
Extend the front leveling legs if necessary
39
Rotate the adjusting rod clockwise to extend the rear leg
40
Rethread the screws to secure the mounting brackets to the cabinet or countertop
41
Feed the drain hose through the cabinet and connect it to the sink drain or disposer
42
"For smaller ports, you can insert the adapter into the house for a better fit"
43
Make sure the hose is elevated above the connection point
44
Thread the water supply line elbow fitting onto the inlet valve port and tighten
45
Realign the lower access panel and rethread the screws to secure
46
3",Turn the water supply and power back on
Description
This video provides step-by-step instructions for replacing the drain hose on Electrolux dishwashers.
All of the information in this video is applicable to the following brands: Electrolux
All of the information in this video is applicable to the following brands: Electrolux
Step-By-Step Instructions
1
Electrolux Dishwasher - 24ID75SPS3A
2
Dishwasher Drain Hose Replacement
3
2, 1, 3",You will need to fully uninstall the appliance
4
3",Turn off the power and water supply to the appliance
5
"Using a phillips-head screwdriver, unthread the two mounting screws securing the lower access panel"
6
Set the panel aside
7
Use channel-lock pliers to loosen the elbow fitting securing the water supply line to the inlet valve
8
Fully unthread the elbow fitting--be prepared for spilled water
9
Disconnect the drain hose from the sink or garbage disposer and feed it through the cabinet
10
Open the dishwasher door and unthread the two screws securing the dishwasher mounting brackets
11
"To move the dishwasher, you may need to adjust the legs to lower the appliance. Rotate the front legs clockwise to lower the front"
12
"Using the phillips-head screwdriver, rotate the rear leg adjusting rod counter-clockwise to lower the rear"
13
Gently pull the dishwasher away from the cabinet
14
"To tip the dishwasher back, you will probably need to detach the power supply cord from the junction box"
15
"Note the orientation of the power wires and grounding wire, then untwist the wire nuts to disconnect the wires"
16
Have an assistant help you to lift up the front of the appliance and support it
17
Unthread the strain relief nut and detach the strain relief and cord from the junction box
18
Remove the support
19
Tip the appliance back and rest it on the rear panel
20
Release the tab to detach the rear leg adjusting rod
21
"Using pliers, squeeze the retaining clips to release the bottom panel"
22
Depress the tabs to release the drain hose collar from the base
23
Use pliers to release the spring clamp securing the drain hose to the sump and pull the hose off the sump
24
Remove the old hose by pulling it through the base
25
Install the new drain hose by feeding the straight end through the hole in the base
26
Slide a spring clamp over the curved end
27
Attach that end to the sump port and secure it with the clamp
28
Feed the drain hose through the cabinet and connect it to the sink drain or disposer
29
Snap the drain hose collar into the base
30
Align the bottom panel tabs with the slots in the base and snap the panel in place
31
Insert the bottom of the adjusting rod into the hole in the base and snap the upper portion in place
32
Return the dishwasher to its upright position
33
"Fully position the power supply cord and strain relief in the junction box, then thread and tighten the nut"
34
Remove the support
35
"Join the black wires together, the white wires together, and the green wires together, securing them with wire nuts"
36
"With the wires repositioned inside the junction box, realign the cover and rethread the screw"
37
Confirm that the water supply line is positioned in the channel in the base then gently slide the dishwasher back into the cabinet
38
Extend the front leveling legs if necessary
39
Rotate the adjusting rod clockwise to extend the rear leg
40
Rethread the screws to secure the mounting brackets to the cabinet or countertop
41
Feed the drain hose through the cabinet and connect it to the sink drain or disposer
42
"For smaller ports, you can insert the adapter into the house for a better fit"
43
Make sure the hose is elevated above the connection point
44
Thread the water supply line elbow fitting onto the inlet valve port and tighten
45
Realign the lower access panel and rethread the screws to secure
46
3",Turn the water supply and power back on
Applicable Product Model
Related Articles & Videos
09:13
Part Replacement
Electrolux Dishwasher Circulation Pump Assembly Replacement A00223923
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com