Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairElectrolux Dishwasher Circulation Pump Assembly Replacement A00223923 
Electrolux Dishwasher Circulation Pump Assembly Replacement A00223923
Skill Level
Total Parts Cost
$210.07Estimated Savings
$112.5009:13
- Description
This video provides step-by-step instructions for replacing the circulation pump assembly on Electrolux dishwashers.
All of the information in this video is applicable to the following brands: Electrolux
All of the information in this video is applicable to the following brands: Electrolux
Step By Step Instructions
1
To replace the circulation pump assembly in your dishwasher, you will need to fully uninstall the appliance.
2
Before you attempt this, be sure to turn off the power to the dishwasher…
3
…and shut off the water supply valve.
4
Using a phillips-head screwdriver, unthread the two mounting screws securing the lower access panel.
5
Set the panel aside.
6
Use channel-lock pliers to loosen the elbow fitting securing the water supply line to the inlet valve.
7
Fully unthread the elbow fitting – be prepared for some water to spill.
8
Next, disconnect the drain hose from the sink drain or garbage disposer…
9
…and feed it through the cabinet.
10
Next, open the dishwasher door and unthread the two screws securing the dishwasher mounting brackets to the cabinet or countertop.
11
To move the dishwasher, you may need to adjust the legs to lower the appliance.
12
Rotate the front legs clockwise to lower the front.
13
Using the phillips-head screwdriver, rotate the rear leg adjusting rod counter-clockwise to lower the rear of the dishwasher.
14
Now gently pull the dishwasher away from the cabinet.
15
To tip the dishwasher back, you will probably need to detach the power supply cord from the junction box.
16
To do this, unthread the screw to release the junction box cover.
17
Note the orientation of the power wires and grounding wire…then untwist the wire nuts to disconnect the wires.
18
Have an assistant help you to lift up the front of the appliance and support it.
19
Unthread the strain relief nut…
20
…and detach the strain relief and cord from the junction box.
21
Remove the support.
22
Now tip the appliance back and rest it on the rear panel.
23
Release the tab to detach the rear leg adjusting rod.
24
Using pliers, squeeze the retaining clips to release the bottom panel.
25
Disconnect the heater wire connecter and the two grounding wires.
26
Disconnect the motor wire connecter as well.
27
Move the float switch out of the way.
28
Using pliers, release the two spring clamps securing the hose to the water regulator and the hose attached to the sump.
29
Next, unthread the screw securing the right side of the base to the frame.
30
Release the retaining tabs to pull the base away from the frame.
31
Detach the rubber mount from the base and you can remove the old assembly.
32
Prepare the new circulation pump assembly for installation…
33
…by transferring the rubber mount from the old assembly to the new one.
34
Slide the spring clamps over the hoses.
35
Returning to the dishwasher, attach the two hoses to the appropriate ports and secure them with the clamps.
36
Snap the base back into position…
37
…and thread the right-side screw to secure.
38
Insert the rubber mount on the pump assembly into the slots in the base.
39
Connect the motor wire connecter.
40
Connect the heater wire connecter as well as the two grounding wires.
41
Reposition the float switch.
42
Align the bottom panel tabs with the slots in the base and snap the panel into place.
43
Insert the bottom of the adjusting rod into the hole in the base the snap the upper portion in place.
44
Return the dishwasher to its upright position.
45
If necessary, support the front of the appliance.
46
Fully position the power supply cord and strain relief in the junction box…
47
…then thread and tighten the strain relief nut.
48
Remove the support.
49
Join the black wires together, the white wires together, and the green grounding wires together and secure them with the wire nuts.
50
With the wires positioned inside the junction box, realign the cover…
51
…and rethread the screw.
52
Confirm that the end of the drain hose is accessible through the cabinet wall…
53
…and the water supply line is positioned in the channel in the base.
54
Now gently slide the dishwasher back into the cabinet.
55
Extend the front leveling legs if necessary.
56
Rotate the adjusting rod clockwise to extend the rear leg.
57
Rethread the screws to secure the mounting brackets to the cabinet or countertop.
58
Feed the drain hose through the cabinet…
59
…and connect it to the sink drain or disposer.
60
Make sure the hose is elevated above the connection point.
61
Thread the water supply line elbow fitting onto the inlet valve port and tighten.
62
Realign the lower access panel…
63
…and rethread the screws to secure.
64
Turn the water supply back on…
65
…as well as the power…
66
…and your dishwasher should be ready for use.
Description
This video provides step-by-step instructions for replacing the circulation pump assembly on Electrolux dishwashers.
All of the information in this video is applicable to the following brands: Electrolux
All of the information in this video is applicable to the following brands: Electrolux
Step-By-Step Instructions
1
To replace the circulation pump assembly in your dishwasher, you will need to fully uninstall the appliance.
2
Before you attempt this, be sure to turn off the power to the dishwasher…
3
…and shut off the water supply valve.
4
Using a phillips-head screwdriver, unthread the two mounting screws securing the lower access panel.
5
Set the panel aside.
6
Use channel-lock pliers to loosen the elbow fitting securing the water supply line to the inlet valve.
7
Fully unthread the elbow fitting – be prepared for some water to spill.
8
Next, disconnect the drain hose from the sink drain or garbage disposer…
9
…and feed it through the cabinet.
10
Next, open the dishwasher door and unthread the two screws securing the dishwasher mounting brackets to the cabinet or countertop.
11
To move the dishwasher, you may need to adjust the legs to lower the appliance.
12
Rotate the front legs clockwise to lower the front.
13
Using the phillips-head screwdriver, rotate the rear leg adjusting rod counter-clockwise to lower the rear of the dishwasher.
14
Now gently pull the dishwasher away from the cabinet.
15
To tip the dishwasher back, you will probably need to detach the power supply cord from the junction box.
16
To do this, unthread the screw to release the junction box cover.
17
Note the orientation of the power wires and grounding wire…then untwist the wire nuts to disconnect the wires.
18
Have an assistant help you to lift up the front of the appliance and support it.
19
Unthread the strain relief nut…
20
…and detach the strain relief and cord from the junction box.
21
Remove the support.
22
Now tip the appliance back and rest it on the rear panel.
23
Release the tab to detach the rear leg adjusting rod.
24
Using pliers, squeeze the retaining clips to release the bottom panel.
25
Disconnect the heater wire connecter and the two grounding wires.
26
Disconnect the motor wire connecter as well.
27
Move the float switch out of the way.
28
Using pliers, release the two spring clamps securing the hose to the water regulator and the hose attached to the sump.
29
Next, unthread the screw securing the right side of the base to the frame.
30
Release the retaining tabs to pull the base away from the frame.
31
Detach the rubber mount from the base and you can remove the old assembly.
32
Prepare the new circulation pump assembly for installation…
33
…by transferring the rubber mount from the old assembly to the new one.
34
Slide the spring clamps over the hoses.
35
Returning to the dishwasher, attach the two hoses to the appropriate ports and secure them with the clamps.
36
Snap the base back into position…
37
…and thread the right-side screw to secure.
38
Insert the rubber mount on the pump assembly into the slots in the base.
39
Connect the motor wire connecter.
40
Connect the heater wire connecter as well as the two grounding wires.
41
Reposition the float switch.
42
Align the bottom panel tabs with the slots in the base and snap the panel into place.
43
Insert the bottom of the adjusting rod into the hole in the base the snap the upper portion in place.
44
Return the dishwasher to its upright position.
45
If necessary, support the front of the appliance.
46
Fully position the power supply cord and strain relief in the junction box…
47
…then thread and tighten the strain relief nut.
48
Remove the support.
49
Join the black wires together, the white wires together, and the green grounding wires together and secure them with the wire nuts.
50
With the wires positioned inside the junction box, realign the cover…
51
…and rethread the screw.
52
Confirm that the end of the drain hose is accessible through the cabinet wall…
53
…and the water supply line is positioned in the channel in the base.
54
Now gently slide the dishwasher back into the cabinet.
55
Extend the front leveling legs if necessary.
56
Rotate the adjusting rod clockwise to extend the rear leg.
57
Rethread the screws to secure the mounting brackets to the cabinet or countertop.
58
Feed the drain hose through the cabinet…
59
…and connect it to the sink drain or disposer.
60
Make sure the hose is elevated above the connection point.
61
Thread the water supply line elbow fitting onto the inlet valve port and tighten.
62
Realign the lower access panel…
63
…and rethread the screws to secure.
64
Turn the water supply back on…
65
…as well as the power…
66
…and your dishwasher should be ready for use.
Applicable Product Model
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com