Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairElectrolux Dishwasher Fill Tank Outlet Hose Replacement A01256402 
Electrolux Dishwasher Fill Tank Outlet Hose Replacement A01256402
Skill Level
Total Parts Cost
$45.94Estimated Savings
$112.5004:48
- Description
This video provides step-by-step instructions for replacing the fill tank outlet hose on Electrolux dishwashers.
All of the information in this video is applicable to the following brands: Electrolux
All of the information in this video is applicable to the following brands: Electrolux
Step By Step Instructions
1
To replace the fill tank outlet hose in your dishwasher, you will need to fully uninstall the appliance.
2
Before you attempt this, be sure to turn off the power to the dishwasher…
3
…and shut off the water supply valve.
4
Using a phillips-head screwdriver, unthread the two mounting screws securing the lower access panel.
5
Set the panel aside.
6
Use channel-lock pliers to loosen the elbow fitting securing the water supply line to the inlet valve.
7
Fully unthread the elbow fitting – be prepared for some water to spill.
8
Next, disconnect the drain hose from the sink drain or garbage disposer…
9
…and feed it through the cabinet.
10
Next, open the dishwasher door and unthread the two screws securing the dishwasher mounting brackets to the cabinet or countertop.
11
To move the dishwasher, you may need to adjust the legs to lower the appliance.
12
Rotate the front legs clockwise to lower the front.
13
Using the phillips-head screwdriver, rotate the rear leg adjusting rod counter-clockwise to lower the rear of the dishwasher.
14
Now gently pull the dishwasher away from the cabinet.
15
Lift up the left-side insulation.
16
Detach the vent hose from the blower housing and vent.
17
Release the retaing tabs to detach the outlet hose from the fill tank…and pull the old hose free of the sump.
18
Install the new fill tank outlet hose…
19
…by inserting the shorter end into the sump port…
20
…then secure the longer end in the fill tank.
21
Reinstall the vent hose.
22
Reposition the insulation.
23
Confirm that the end of the drain hose is accessible through the cabinet wall…
24
…then gently slide the dishwasher back into the cabinet.
25
Extend the front leveling legs if necessary.
26
Rotate the adjusting rod clockwise to extend the rear leg.
27
Rethread the screws to secure the mounting brackets to the cabinet or countertop.
28
Feed the drain hose through the cabinet…
29
…and connect it to the sink drain or disposer.
30
Make sure the hose is elevated above the connection point.
31
Thread the water supply line elbow fitting onto the inlet valve port and tighten.
32
Realign the lower access panel…
33
…and rethread the screws to secure.
34
Turn the water supply back on…
35
…as well as the power…
36
…and your dishwasher should be ready for use.
Description
This video provides step-by-step instructions for replacing the fill tank outlet hose on Electrolux dishwashers.
All of the information in this video is applicable to the following brands: Electrolux
All of the information in this video is applicable to the following brands: Electrolux
Step-By-Step Instructions
1
To replace the fill tank outlet hose in your dishwasher, you will need to fully uninstall the appliance.
2
Before you attempt this, be sure to turn off the power to the dishwasher…
3
…and shut off the water supply valve.
4
Using a phillips-head screwdriver, unthread the two mounting screws securing the lower access panel.
5
Set the panel aside.
6
Use channel-lock pliers to loosen the elbow fitting securing the water supply line to the inlet valve.
7
Fully unthread the elbow fitting – be prepared for some water to spill.
8
Next, disconnect the drain hose from the sink drain or garbage disposer…
9
…and feed it through the cabinet.
10
Next, open the dishwasher door and unthread the two screws securing the dishwasher mounting brackets to the cabinet or countertop.
11
To move the dishwasher, you may need to adjust the legs to lower the appliance.
12
Rotate the front legs clockwise to lower the front.
13
Using the phillips-head screwdriver, rotate the rear leg adjusting rod counter-clockwise to lower the rear of the dishwasher.
14
Now gently pull the dishwasher away from the cabinet.
15
Lift up the left-side insulation.
16
Detach the vent hose from the blower housing and vent.
17
Release the retaing tabs to detach the outlet hose from the fill tank…and pull the old hose free of the sump.
18
Install the new fill tank outlet hose…
19
…by inserting the shorter end into the sump port…
20
…then secure the longer end in the fill tank.
21
Reinstall the vent hose.
22
Reposition the insulation.
23
Confirm that the end of the drain hose is accessible through the cabinet wall…
24
…then gently slide the dishwasher back into the cabinet.
25
Extend the front leveling legs if necessary.
26
Rotate the adjusting rod clockwise to extend the rear leg.
27
Rethread the screws to secure the mounting brackets to the cabinet or countertop.
28
Feed the drain hose through the cabinet…
29
…and connect it to the sink drain or disposer.
30
Make sure the hose is elevated above the connection point.
31
Thread the water supply line elbow fitting onto the inlet valve port and tighten.
32
Realign the lower access panel…
33
…and rethread the screws to secure.
34
Turn the water supply back on…
35
…as well as the power…
36
…and your dishwasher should be ready for use.
Applicable Product Model
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com