Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairElectrolux Dishwasher Water Supply Manifold Replacement A00023201 
Electrolux Dishwasher Water Supply Manifold Replacement A00023201
Skill Level
Total Parts Cost
$163.31Estimated Savings
$112.5007:41
- Description
This video provides step-by-step instructions for replacing the water supply manifold on Electrolux dishwashers.
All of the information in this video is applicable to the following brands: Electrolux
All of the information in this video is applicable to the following brands: Electrolux
Step By Step Instructions
1
To replace the water supply manifold in your dishwasher, you will need to fully uninstall the appliance.
2
Before you attempt this, be sure to turn off the power to the dishwasher…
3
…and shut off the water supply valve.
4
Using a phillips-head screwdriver, unthread the two mounting screws securing the lower access panel.
5
Set the panel aside.
6
Use channel-lock pliers to loosen the elbow fitting securing the water supply line to the inlet valve.
7
Fully unthread the elbow fitting – be prepared for some water to spill.
8
Next, disconnect the drain hose from the sink drain or garbage disposer…
9
…and feed it through the cabinet.
10
Next, open the dishwasher door and unthread the two screws securing the dishwasher mounting brackets to the cabinet or countertop.
11
To move the dishwasher, you may need to adjust the legs to lower the appliance.
12
Rotate the front legs clockwise to lower the front.
13
Using the phillips-head screwdriver, rotate the rear leg adjusting rod counter-clockwise to lower the rear of the dishwasher.
14
Now gently pull the dishwasher away from the cabinet.
15
Place a weight on top of the dishwasher to help stabilize it.
16
Fully remove the lower dishrack.
17
Pull the upper dishrack out…
18
…and rotate both front stop clips outward to fully remove the rack.
19
Pull the top rack out.
20
Release the retaining tabs to remove the front stop clips.
21
Slide the rack off of the rails.
22
Pull the lower wash arm straight up to remove.
23
Rotate the drain filter counter-clockwise to remove.
24
Lift off the flat filter.
25
Using the phillips-head screwdriver, unthread the two mounting screws securing the wash arm support.
26
Place a two-by-four piece of wood under the water supply manifold elbow and you can press down on the wash arm support to fully remove it from the manifold.
27
Reach under the insulation and rotate the manifold retaining nut counter-clockwise to remove.
28
Pull the rear retaining tabs outward to fully release the old manifold.
29
Prepare the new water supply manifold for installation…
30
…by transferring the wash arm from the old manifold to the new one.
31
Confirm the two rubber seals are intact on the outlet ports.
32
Now align the new manifold with the rear retaining tabs and snap it into place.
33
Insert the nub on the top of the manifold into the upper hole.
34
With the side with the rubber o-ring facing down, align the retaining nut on the nub and rotate clockwise to secure the manifold.
35
Snap the wash arm support into place on the water supply manifold.
36
Align the support on the sump…
37
…and thread the two mounting screws.
38
Realign the flat filter.
39
Realign the drain filter in the sump then rotate clockwise to lock it into place.
40
Align the wash arm on the support and snap it into place.
41
Replace the lower dishrack.
42
Align the utensil tray support brackets on the rails and slide the top rack in.
43
Realign the two front stop clips on the rails and snap them into place.
44
Realign the upper dishrack rollers on the slide rails, push the rack in…
45
…and rotate the front stop clips inward.
46
Remove the weight.
47
Confirm that the end of the drain hose is accessible through the cabinet wall…
48
…then gently slide the dishwasher back into the cabinet.
49
Extend the front leveling legs if necessary.
50
Rotate the adjusting rod clockwise to extend the rear leg.
51
Rethread the screws to secure the mounting brackets to the cabinet or countertop.
52
Feed the drain hose through the cabinet…
53
…and connect it to the sink drain or disposer.
54
Make sure the hose is elevated above the connection point.
55
Thread the water supply line elbow fitting onto the inlet valve port and tighten.
56
Realign the lower access panel…
57
…and rethread the screws to secure.
58
Turn the water supply back on…
59
…as well as the power…
60
…and your dishwasher should be ready for use.
Description
This video provides step-by-step instructions for replacing the water supply manifold on Electrolux dishwashers.
All of the information in this video is applicable to the following brands: Electrolux
All of the information in this video is applicable to the following brands: Electrolux
Step-By-Step Instructions
1
To replace the water supply manifold in your dishwasher, you will need to fully uninstall the appliance.
2
Before you attempt this, be sure to turn off the power to the dishwasher…
3
…and shut off the water supply valve.
4
Using a phillips-head screwdriver, unthread the two mounting screws securing the lower access panel.
5
Set the panel aside.
6
Use channel-lock pliers to loosen the elbow fitting securing the water supply line to the inlet valve.
7
Fully unthread the elbow fitting – be prepared for some water to spill.
8
Next, disconnect the drain hose from the sink drain or garbage disposer…
9
…and feed it through the cabinet.
10
Next, open the dishwasher door and unthread the two screws securing the dishwasher mounting brackets to the cabinet or countertop.
11
To move the dishwasher, you may need to adjust the legs to lower the appliance.
12
Rotate the front legs clockwise to lower the front.
13
Using the phillips-head screwdriver, rotate the rear leg adjusting rod counter-clockwise to lower the rear of the dishwasher.
14
Now gently pull the dishwasher away from the cabinet.
15
Place a weight on top of the dishwasher to help stabilize it.
16
Fully remove the lower dishrack.
17
Pull the upper dishrack out…
18
…and rotate both front stop clips outward to fully remove the rack.
19
Pull the top rack out.
20
Release the retaining tabs to remove the front stop clips.
21
Slide the rack off of the rails.
22
Pull the lower wash arm straight up to remove.
23
Rotate the drain filter counter-clockwise to remove.
24
Lift off the flat filter.
25
Using the phillips-head screwdriver, unthread the two mounting screws securing the wash arm support.
26
Place a two-by-four piece of wood under the water supply manifold elbow and you can press down on the wash arm support to fully remove it from the manifold.
27
Reach under the insulation and rotate the manifold retaining nut counter-clockwise to remove.
28
Pull the rear retaining tabs outward to fully release the old manifold.
29
Prepare the new water supply manifold for installation…
30
…by transferring the wash arm from the old manifold to the new one.
31
Confirm the two rubber seals are intact on the outlet ports.
32
Now align the new manifold with the rear retaining tabs and snap it into place.
33
Insert the nub on the top of the manifold into the upper hole.
34
With the side with the rubber o-ring facing down, align the retaining nut on the nub and rotate clockwise to secure the manifold.
35
Snap the wash arm support into place on the water supply manifold.
36
Align the support on the sump…
37
…and thread the two mounting screws.
38
Realign the flat filter.
39
Realign the drain filter in the sump then rotate clockwise to lock it into place.
40
Align the wash arm on the support and snap it into place.
41
Replace the lower dishrack.
42
Align the utensil tray support brackets on the rails and slide the top rack in.
43
Realign the two front stop clips on the rails and snap them into place.
44
Realign the upper dishrack rollers on the slide rails, push the rack in…
45
…and rotate the front stop clips inward.
46
Remove the weight.
47
Confirm that the end of the drain hose is accessible through the cabinet wall…
48
…then gently slide the dishwasher back into the cabinet.
49
Extend the front leveling legs if necessary.
50
Rotate the adjusting rod clockwise to extend the rear leg.
51
Rethread the screws to secure the mounting brackets to the cabinet or countertop.
52
Feed the drain hose through the cabinet…
53
…and connect it to the sink drain or disposer.
54
Make sure the hose is elevated above the connection point.
55
Thread the water supply line elbow fitting onto the inlet valve port and tighten.
56
Realign the lower access panel…
57
…and rethread the screws to secure.
58
Turn the water supply back on…
59
…as well as the power…
60
…and your dishwasher should be ready for use.
Applicable Product Model
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com