Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairElectrolux Dishwasher Water Regulator Replacement A00001202 
Electrolux Dishwasher Water Regulator Replacement A00001202
Skill Level
Total Parts Cost
$201.12Estimated Savings
$112.5008:10
- Description
This video provides step-by-step instructions for replacing the water regulator on Electrolux dishwashers.
All of the information in this video is applicable to the following brands: Electrolux
All of the information in this video is applicable to the following brands: Electrolux
Step By Step Instructions
1
Electrolux Dishwasher - 24ID75SPS3A
2
Dishwasher Water Regulator Replacement
3
"Heavy, Sharp, Shock, Water"
4
You will need to fully uninstall the appliance
5
"Shock, Water"
6
Turn off the power and water supply to the appliance
7
"Using a phillips-head screwdriver, unthread the two mounting screws securing the lower access panel"
8
Sharp
9
Use channel-lock pliers to loosen the elbow fitting securing the water supply line to the inlet valve
10
Fully unthread the elbow fitting--be prepared for spilled water
11
Disconnect the drain hose from the sink or garbage disposer and feed it through the cabinet
12
Open the dishwasher door and unthread the two screws securing the dishwasher mounting brackets
13
"To move the dishwasher, you may need to adjust the legs to lower the appliance. Rotate the front legs clockwise to lower the front"
14
"Using the phillips-head screwdriver, rotate the rear leg adjusting rod counter-clockwise to lower the rear"
15
Heavy
16
Gently pull the dishwasher away from the cabinet
17
"To tip the dishwasher back, you will probably need to detach the power supply cord from the junction box"
18
Unthread the screw cover to release the junction box cover
19
"Note the orientation of the power wires and grounding wire, then untwist the wire nuts to disconnect the wires"
20
Heavy
21
Have an assistant help you to lift up the front of the appliance and support it
22
Unthread the strain relief nut and detach the strain relief and cord from the junction box
23
Remove the support
24
Tip the appliance back and rest it on the rear panel
25
Release the tab to detach the rear leg adjusting rod
26
"Using pliers, squeeze the retaining clips to release the bottom panel"
27
Disconnect the water regulator wire connector
28
Unthread the two mounting screws securing the regulator to the sump
29
Move the float switch out of the way
30
Use pliers to release the spring clamp securing the drain hose to the sump and pull the old water regulator free of the sump and off of the hose
31
Transfer the two O-rings from the sump to the regulator ports on the new regulator
32
Attach the hose to the regulator then align it with the sump and push it into place
33
Thread the two mounting screws and clamp the hose
34
Connect the wire connecter and reposition the float switch
35
Align the bottom panel tabs with the slots in the base and snap the panel in place
36
Insert the bottom of the adjusting rod into the hole in the base then snap the upper portion in place
37
Return the dishwasher to its upright position
38
"Fully position the power supply cord and strain relief in the junction box, then thread and tighten the nut"
39
Remove the support
40
"Join the black wires together, the white wires together, and the green wires together, securing them with wire nuts"
41
"With the wires repositioned inside the junction box, realign the cover and rethread the screw"
42
Confirm that the water supply line is positioned in the channel in the base then gently slide the dishwasher back into the cabinet
43
Gently slide the dishwasher back into the cabinet
44
Extend the front leveling legs if necessary
45
Rotate the adjusting rod clockwise to extend the rear leg
46
Rethread the screws to secure the mounting brackets to the cabinet or countertop
47
Feed the drain hose through the cabinet and connect it to the sink drain or disposer
48
Make sure the hose is elevated above the connection point
49
Thread the water supply line elbow fitting onto the inlet valve port and tighten
50
Realign the lower access panel and rethread the screws to secure
51
3",Turn the water supply and power back on
Description
This video provides step-by-step instructions for replacing the water regulator on Electrolux dishwashers.
All of the information in this video is applicable to the following brands: Electrolux
All of the information in this video is applicable to the following brands: Electrolux
Step-By-Step Instructions
1
Electrolux Dishwasher - 24ID75SPS3A
2
Dishwasher Water Regulator Replacement
3
"Heavy, Sharp, Shock, Water"
4
You will need to fully uninstall the appliance
5
"Shock, Water"
6
Turn off the power and water supply to the appliance
7
"Using a phillips-head screwdriver, unthread the two mounting screws securing the lower access panel"
8
Sharp
9
Use channel-lock pliers to loosen the elbow fitting securing the water supply line to the inlet valve
10
Fully unthread the elbow fitting--be prepared for spilled water
11
Disconnect the drain hose from the sink or garbage disposer and feed it through the cabinet
12
Open the dishwasher door and unthread the two screws securing the dishwasher mounting brackets
13
"To move the dishwasher, you may need to adjust the legs to lower the appliance. Rotate the front legs clockwise to lower the front"
14
"Using the phillips-head screwdriver, rotate the rear leg adjusting rod counter-clockwise to lower the rear"
15
Heavy
16
Gently pull the dishwasher away from the cabinet
17
"To tip the dishwasher back, you will probably need to detach the power supply cord from the junction box"
18
Unthread the screw cover to release the junction box cover
19
"Note the orientation of the power wires and grounding wire, then untwist the wire nuts to disconnect the wires"
20
Heavy
21
Have an assistant help you to lift up the front of the appliance and support it
22
Unthread the strain relief nut and detach the strain relief and cord from the junction box
23
Remove the support
24
Tip the appliance back and rest it on the rear panel
25
Release the tab to detach the rear leg adjusting rod
26
"Using pliers, squeeze the retaining clips to release the bottom panel"
27
Disconnect the water regulator wire connector
28
Unthread the two mounting screws securing the regulator to the sump
29
Move the float switch out of the way
30
Use pliers to release the spring clamp securing the drain hose to the sump and pull the old water regulator free of the sump and off of the hose
31
Transfer the two O-rings from the sump to the regulator ports on the new regulator
32
Attach the hose to the regulator then align it with the sump and push it into place
33
Thread the two mounting screws and clamp the hose
34
Connect the wire connecter and reposition the float switch
35
Align the bottom panel tabs with the slots in the base and snap the panel in place
36
Insert the bottom of the adjusting rod into the hole in the base then snap the upper portion in place
37
Return the dishwasher to its upright position
38
"Fully position the power supply cord and strain relief in the junction box, then thread and tighten the nut"
39
Remove the support
40
"Join the black wires together, the white wires together, and the green wires together, securing them with wire nuts"
41
"With the wires repositioned inside the junction box, realign the cover and rethread the screw"
42
Confirm that the water supply line is positioned in the channel in the base then gently slide the dishwasher back into the cabinet
43
Gently slide the dishwasher back into the cabinet
44
Extend the front leveling legs if necessary
45
Rotate the adjusting rod clockwise to extend the rear leg
46
Rethread the screws to secure the mounting brackets to the cabinet or countertop
47
Feed the drain hose through the cabinet and connect it to the sink drain or disposer
48
Make sure the hose is elevated above the connection point
49
Thread the water supply line elbow fitting onto the inlet valve port and tighten
50
Realign the lower access panel and rethread the screws to secure
51
3",Turn the water supply and power back on
Applicable Product Model
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com