Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairElectrolux Dishwasher Upper Dishrack Rail Roller Support Replacement 152122010 
Electrolux Dishwasher Upper Dishrack Rail Roller Support Replacement 152122010
Skill Level
Total Parts Cost
$24.57Estimated Savings
$112.5005:44
- Description
This video provides step-by-step instructions for replacing the upper dishrack rail roller support on Electrolux dishwashers.
All of the information in this video is applicable to the following brands: Electrolux
All of the information in this video is applicable to the following brands: Electrolux
Step By Step Instructions
1
Electrolux Dishwasher - 24ID75SPS3A
2
Dishwasher Upper Dishrack Rail Roller Support Replacement
3
2, 1, 3",You will need to fully uninstall the appliance
4
Fully shut off the power and water to the appliance
5
"Using a phillips-head screwdriver, unthread the two mounting screws securing the lower access panel"
6
Set the panel aside
7
Use channel-lock pliers to loosen the elbow fitting securing the water supply line to the inlet valve
8
Fully unthread the elbow fitting--be prepared for spilled water
9
Disconnect the drain hose from the sink or garbage disposer and feed it through the cabinet
10
Open the dishwasher door and unthread the two screws securing the dishwasher mounting brackets
11
"To move the dishwasher, you may need to adjust the legs to lower the appliance. Rotate the front legs clockwise to lower the front"
12
Use the phillips-head screwdriver to rotate the rear leg adjusting rod counter-clockwise to lower the rear
13
Gently pull the dishwasher away from the cabinet
14
Place a weight on top of the dishwasher to stabilize
15
Pull the upper dishrack out and rotate both front stop clips outward to fully remove the rack
16
Release the retaining tabs to remove the appropriate rear stop clip and slide the rail out
17
Lift up the insulation and unthread the screws securing the old roller support
18
Install the new roller support by realigning the rollers on the inside of the side panel and then aligning the new support on the outside of the panel
19
Thread the screws to secure then realign the insulation
20
Realign the rail on the rollers and snap the rear stop clip into place
21
"Realign the upper dishrack rollers on the slide rails, push the rack in and rotate the front stop clips inward"
22
Remove the weight and confirm that the end of the drain hose is accessible
23
Gently slide the dishwasher back into the cabinet
24
Extend the front leveling legs if necessary
25
Rotate the adjusting rod clockwise to extend the rear leg
26
Rethread the screws to secure the mounting brackets to the cabinet or countertop
27
Feed the drain hose through the cabinet and connect it to the sink drain or disposer
28
Make sure the hose is elevated above the connection point
29
Thread the water supply line elbow fitting onto the inlet valve port and tighten
30
Realign the lower access panel and rethread the screws to secure
31
3",Turn the water supply and power back on
Description
This video provides step-by-step instructions for replacing the upper dishrack rail roller support on Electrolux dishwashers.
All of the information in this video is applicable to the following brands: Electrolux
All of the information in this video is applicable to the following brands: Electrolux
Step-By-Step Instructions
1
Electrolux Dishwasher - 24ID75SPS3A
2
Dishwasher Upper Dishrack Rail Roller Support Replacement
3
2, 1, 3",You will need to fully uninstall the appliance
4
Fully shut off the power and water to the appliance
5
"Using a phillips-head screwdriver, unthread the two mounting screws securing the lower access panel"
6
Set the panel aside
7
Use channel-lock pliers to loosen the elbow fitting securing the water supply line to the inlet valve
8
Fully unthread the elbow fitting--be prepared for spilled water
9
Disconnect the drain hose from the sink or garbage disposer and feed it through the cabinet
10
Open the dishwasher door and unthread the two screws securing the dishwasher mounting brackets
11
"To move the dishwasher, you may need to adjust the legs to lower the appliance. Rotate the front legs clockwise to lower the front"
12
Use the phillips-head screwdriver to rotate the rear leg adjusting rod counter-clockwise to lower the rear
13
Gently pull the dishwasher away from the cabinet
14
Place a weight on top of the dishwasher to stabilize
15
Pull the upper dishrack out and rotate both front stop clips outward to fully remove the rack
16
Release the retaining tabs to remove the appropriate rear stop clip and slide the rail out
17
Lift up the insulation and unthread the screws securing the old roller support
18
Install the new roller support by realigning the rollers on the inside of the side panel and then aligning the new support on the outside of the panel
19
Thread the screws to secure then realign the insulation
20
Realign the rail on the rollers and snap the rear stop clip into place
21
"Realign the upper dishrack rollers on the slide rails, push the rack in and rotate the front stop clips inward"
22
Remove the weight and confirm that the end of the drain hose is accessible
23
Gently slide the dishwasher back into the cabinet
24
Extend the front leveling legs if necessary
25
Rotate the adjusting rod clockwise to extend the rear leg
26
Rethread the screws to secure the mounting brackets to the cabinet or countertop
27
Feed the drain hose through the cabinet and connect it to the sink drain or disposer
28
Make sure the hose is elevated above the connection point
29
Thread the water supply line elbow fitting onto the inlet valve port and tighten
30
Realign the lower access panel and rethread the screws to secure
31
3",Turn the water supply and power back on
Applicable Product Model
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com