Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairSamsung Refrigerator Flapper Camera Control Board Replacement
Samsung Refrigerator Flapper Camera Control Board Replacement
Total Parts Cost
$NaN05:35
- Description
This video provides step-by-step repair instructions for replacing the flapper camera control board on a Samsung Refrigerator (Model RF27T5501SRAA51). The most common reason for replacing this part is if the camera is not working at all.
All of the information for this video is applicable to the following brands:
Samsung
All of the information for this video is applicable to the following brands:
Samsung
Step By Step Instructions
1
To replace the flapper camera control board in this Samsung refrigerator,
2
You will need a Phillips head screwdriver, a small flat head screwdriver, a putty knife, and a mallet.
3
Before you begin the procedure, unplug the appliance's power cord.
4
Open the left side refrigerator door and use the Phillips head screwdriver to unthread the two screws securing the center flapper hinge.
5
Use the mallet to tap the bottom of the flapper to help detach.
6
Pull the wire harnesses out and depress the tabs to disconnect the two wire harness connectors.
7
Next, use the putty knife to pry out the flapper heater.
8
Now use the small flathead screwdriver to separate the inner flapper panel from the outer panel.
9
Remove the foam inserts.
10
Use the small flathead screwdriver to release the tab to detach the camera control board.
11
Disconnect the main wire connector along with the three camera wire connectors to fully remove the old board.
12
To install the new flapper camera control board, first connect the four wire connectors to the appropriate terminals.
13
Snap the board into place in the outer panel.
14
Replace the foam inserts.
15
Confirm the rubber grommet is in place on the bottom of the inner flapper panel.
16
Then align the inner panel with the outer panel and snap it into position.
17
Realign the flapper heater and snap it into place.
18
Reinstall the flapper by first connecting the two wire connectors.
19
Push the wire harnesses into the inner liner.
20
Then align the upper and lower hinges on the liner mounting posts and slide the flapper down.
21
Re-thread the two screws to secure the center hinge.
22
Plug the power cord back in and the refrigerator should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the flapper camera control board on a Samsung Refrigerator (Model RF27T5501SRAA51). The most common reason for replacing this part is if the camera is not working at all.
All of the information for this video is applicable to the following brands:
Samsung
All of the information for this video is applicable to the following brands:
Samsung
Step-By-Step Instructions
1
To replace the flapper camera control board in this Samsung refrigerator,
2
You will need a Phillips head screwdriver, a small flat head screwdriver, a putty knife, and a mallet.
3
Before you begin the procedure, unplug the appliance's power cord.
4
Open the left side refrigerator door and use the Phillips head screwdriver to unthread the two screws securing the center flapper hinge.
5
Use the mallet to tap the bottom of the flapper to help detach.
6
Pull the wire harnesses out and depress the tabs to disconnect the two wire harness connectors.
7
Next, use the putty knife to pry out the flapper heater.
8
Now use the small flathead screwdriver to separate the inner flapper panel from the outer panel.
9
Remove the foam inserts.
10
Use the small flathead screwdriver to release the tab to detach the camera control board.
11
Disconnect the main wire connector along with the three camera wire connectors to fully remove the old board.
12
To install the new flapper camera control board, first connect the four wire connectors to the appropriate terminals.
13
Snap the board into place in the outer panel.
14
Replace the foam inserts.
15
Confirm the rubber grommet is in place on the bottom of the inner flapper panel.
16
Then align the inner panel with the outer panel and snap it into position.
17
Realign the flapper heater and snap it into place.
18
Reinstall the flapper by first connecting the two wire connectors.
19
Push the wire harnesses into the inner liner.
20
Then align the upper and lower hinges on the liner mounting posts and slide the flapper down.
21
Re-thread the two screws to secure the center hinge.
22
Plug the power cord back in and the refrigerator should be ready for use.
Applicable Product Model
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com