Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairSamsung Refrigerator Right Freezer Rail Support Replacement DA63-03415A
Samsung Refrigerator Right Freezer Rail Support Replacement DA63-03415A
Skill Level
Total Parts Cost
$57.78Estimated Savings
$112.5004:17
- Description
This video provides step-by-step repair instructions for replacing the right freezer rail support on a Samsung Refrigerator (Model RF27T5501SRAA51). The most common reason for replacing this part is if it is damaged or missing.
All of the information for this video is applicable to the following brands:
Samsung
All of the information for this video is applicable to the following brands:
Samsung
Step By Step Instructions
1
To replace the lower right freezer drawer rail support in this Samsung refrigerator, you will need a Phillips head screwdriver, a small flathead screwdriver, and a 10 millimeter socket.
2
Before you begin the procedure, unplug the appliance's power cord.
3
Open the freezer drawer and remove both baskets.
4
Use the 10 millimeter socket to unthread the two screws securing the left support bracket.
5
Unthread the two screws securing the right support bracket as well.
6
Tilt the drawer front forward, then lift up to remove.
7
Use the small flathead screwdriver to detach the retaining pin securing the gear shaft.
8
Slide the gear shaft to the right to remove.
9
Depress the tab and carefully remove the freezer drawer rail assembly.
10
You can now use the Phillips head screwdriver to unthread the three screws securing the rail support to the liner.
11
Pull the old support out and forward to remove.
12
To install the new freezer drawer rail support, insert the tab into the slot in the liner and push back.
13
Thread the three screws to secure.
14
Reinstall the drawer rail assembly by aligning it on the support and pushing back until it snaps into place.
15
Be aware you will need to adjust the gear to confirm the gear shaft will align with both gears.
16
Reinstall the gear shaft by inserting the end of the shaft with the retaining pin hole in the right side gear first, then insert the opposite end of the shaft into the left side gear.
17
Snap the retaining pin into place to secure the shaft.
18
Reinstall the drawer front by aligning the support bracket tabs with the slots on the rails.
19
Thread and tighten the left and right side screws to secure the brackets to the rails.
20
Replace the two baskets.
21
Plug the power cord back in, and the refrigerator should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the right freezer rail support on a Samsung Refrigerator (Model RF27T5501SRAA51). The most common reason for replacing this part is if it is damaged or missing.
All of the information for this video is applicable to the following brands:
Samsung
All of the information for this video is applicable to the following brands:
Samsung
Step-By-Step Instructions
1
To replace the lower right freezer drawer rail support in this Samsung refrigerator, you will need a Phillips head screwdriver, a small flathead screwdriver, and a 10 millimeter socket.
2
Before you begin the procedure, unplug the appliance's power cord.
3
Open the freezer drawer and remove both baskets.
4
Use the 10 millimeter socket to unthread the two screws securing the left support bracket.
5
Unthread the two screws securing the right support bracket as well.
6
Tilt the drawer front forward, then lift up to remove.
7
Use the small flathead screwdriver to detach the retaining pin securing the gear shaft.
8
Slide the gear shaft to the right to remove.
9
Depress the tab and carefully remove the freezer drawer rail assembly.
10
You can now use the Phillips head screwdriver to unthread the three screws securing the rail support to the liner.
11
Pull the old support out and forward to remove.
12
To install the new freezer drawer rail support, insert the tab into the slot in the liner and push back.
13
Thread the three screws to secure.
14
Reinstall the drawer rail assembly by aligning it on the support and pushing back until it snaps into place.
15
Be aware you will need to adjust the gear to confirm the gear shaft will align with both gears.
16
Reinstall the gear shaft by inserting the end of the shaft with the retaining pin hole in the right side gear first, then insert the opposite end of the shaft into the left side gear.
17
Snap the retaining pin into place to secure the shaft.
18
Reinstall the drawer front by aligning the support bracket tabs with the slots on the rails.
19
Thread and tighten the left and right side screws to secure the brackets to the rails.
20
Replace the two baskets.
21
Plug the power cord back in, and the refrigerator should be ready for use.
Applicable Product Model
Parts Needed
Drawer Slide Rail Cover
$57.78
Total$0.00
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com