Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairSamsung Refrigerator Auger Motor Replacement DA31-00105M
Samsung Refrigerator Auger Motor Replacement DA31-00105M
Skill Level
Total Parts Cost
$221.29Estimated Savings
$112.5008:43
- Description
This video provides step-by-step repair instructions for replacing the auger motor on a Samsung Refrigerator (Model RF27T5501SRAA51). The most common reason for replacing this part is if the ice maker will not dispense ice.
All of the information for this video is applicable to the following brands:
Samsung
All of the information for this video is applicable to the following brands:
Samsung
Step By Step Instructions
1
To replace the ice auger motor in this samsung refrigerator…
2
… you will need a phillips-head screwdriver, a large flat-head screwdriver, and a small flat-head screwdriver.
3
Before you begin the procedure, unplug the appliance’s power cord.
4
Open the left-side refrigerator door…
5
… and pull out the ice bucket.
6
Using the phillips-head screwdriver, unthread the screw securing the ice wire harness cover.
7
With the screw unthreaded, you can pull the cover straight out to remove.
8
Depress the tabs to disconnect the wire harness connecter.
9
Next, unthread the screw securing the lower ice maker cover.
10
Use the large flat-head screwdriver to depress the retaining tab to release the cover.
11
Use the screwdriver to help detach the refrigerant tubing from the bottom of the ice maker.
12
Now depress the retaining tab at the top and pull the ice maker assembly forward and down to remove – this may require some effort.
13
Next, use the small flat-head screwdriver to depress the retaining tab to disconnect the auger wire harness connecter.
14
Insert the large flat-head screwdriver under the auger motor assembly retaining clip then rotate to lift up the clip.
15
You can now pull the assembly out.
16
Unthread the screw securing the solenoid bracket cover.
17
Use the small flat-head screwdriver to depress the three tabs to release the cover.
18
Use the large flat-head screwdriver to help loosen the nut so you can unthread the nut and auger drive gear from the motor shaft.
19
Disconnect the motor wire connecter and use the phillips-head screwdriver to unthread the screw to release the grounding wire from the solenoid.
20
You can now unthread the three mounting screws securing the motor to the housing.
21
With the screws unthreaded, you can now pull the old motor out – this may require some effort.
22
To prepare the new ice auger motor for installation…
23
… transfer the shield from the old motor to the new one.
24
Now feed the grounding wire through the channel in the housing and position the new motor.
25
Thread the three mounting screws to secure.
26
Thread the screw to secure the grounding wire to the solenoid.
27
Connect the motor wire connecter.
28
Thread the auger drive gear and nut onto the new motor shaft and use the screwdriver to tighten.
29
Keeping the wires secure in the slot, realign and snap the solenoid bracket cover into place.
30
Rethread the mounting screw.
31
Confirm all of the wiring is secured.
32
Realign the ice auger motor assembly in the housing and push it back until it locks into place.
33
Connect the auger wire harness connecter.
34
Reposition the ice maker assembly in the housing so the refrigerant tubing feeds through the space between the ice maker tray and the hinged lower cover…
35
… then align the slots on the housing mounting posts and push back until the assembly is fully seated.
36
Press the refrigerant tubing into place under the tray and close the cover.
37
Rethread the screw to secure the cover.
38
Connect the ice wire harness connecter and secure all wiring behind the clips.
39
Realign the tabs on the wire harness cover with the slots in the ice maker housing and push the cover straight back.
40
Thread the screw to secure.
41
Replace the ice bucket.
42
Plug the power cord back in…
43
… and the refrigerator should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the auger motor on a Samsung Refrigerator (Model RF27T5501SRAA51). The most common reason for replacing this part is if the ice maker will not dispense ice.
All of the information for this video is applicable to the following brands:
Samsung
All of the information for this video is applicable to the following brands:
Samsung
Step-By-Step Instructions
1
To replace the ice auger motor in this samsung refrigerator…
2
… you will need a phillips-head screwdriver, a large flat-head screwdriver, and a small flat-head screwdriver.
3
Before you begin the procedure, unplug the appliance’s power cord.
4
Open the left-side refrigerator door…
5
… and pull out the ice bucket.
6
Using the phillips-head screwdriver, unthread the screw securing the ice wire harness cover.
7
With the screw unthreaded, you can pull the cover straight out to remove.
8
Depress the tabs to disconnect the wire harness connecter.
9
Next, unthread the screw securing the lower ice maker cover.
10
Use the large flat-head screwdriver to depress the retaining tab to release the cover.
11
Use the screwdriver to help detach the refrigerant tubing from the bottom of the ice maker.
12
Now depress the retaining tab at the top and pull the ice maker assembly forward and down to remove – this may require some effort.
13
Next, use the small flat-head screwdriver to depress the retaining tab to disconnect the auger wire harness connecter.
14
Insert the large flat-head screwdriver under the auger motor assembly retaining clip then rotate to lift up the clip.
15
You can now pull the assembly out.
16
Unthread the screw securing the solenoid bracket cover.
17
Use the small flat-head screwdriver to depress the three tabs to release the cover.
18
Use the large flat-head screwdriver to help loosen the nut so you can unthread the nut and auger drive gear from the motor shaft.
19
Disconnect the motor wire connecter and use the phillips-head screwdriver to unthread the screw to release the grounding wire from the solenoid.
20
You can now unthread the three mounting screws securing the motor to the housing.
21
With the screws unthreaded, you can now pull the old motor out – this may require some effort.
22
To prepare the new ice auger motor for installation…
23
… transfer the shield from the old motor to the new one.
24
Now feed the grounding wire through the channel in the housing and position the new motor.
25
Thread the three mounting screws to secure.
26
Thread the screw to secure the grounding wire to the solenoid.
27
Connect the motor wire connecter.
28
Thread the auger drive gear and nut onto the new motor shaft and use the screwdriver to tighten.
29
Keeping the wires secure in the slot, realign and snap the solenoid bracket cover into place.
30
Rethread the mounting screw.
31
Confirm all of the wiring is secured.
32
Realign the ice auger motor assembly in the housing and push it back until it locks into place.
33
Connect the auger wire harness connecter.
34
Reposition the ice maker assembly in the housing so the refrigerant tubing feeds through the space between the ice maker tray and the hinged lower cover…
35
… then align the slots on the housing mounting posts and push back until the assembly is fully seated.
36
Press the refrigerant tubing into place under the tray and close the cover.
37
Rethread the screw to secure the cover.
38
Connect the ice wire harness connecter and secure all wiring behind the clips.
39
Realign the tabs on the wire harness cover with the slots in the ice maker housing and push the cover straight back.
40
Thread the screw to secure.
41
Replace the ice bucket.
42
Plug the power cord back in…
43
… and the refrigerator should be ready for use.
Applicable Product Model
Parts Needed
Auger Motor
$221.29
Total$0.00
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com