Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairEcho Hedge Trimmer Blade Replacement #X411000271
Echo Hedge Trimmer Blade Replacement #X411000271
Skill Level
Total Parts Cost
$28.99Estimated Savings
$112.5005:58
- Description
This video provides step-by-step repair instructions for replacing the trimmer blades on an Echo hedge trimmer. The most common reasons for replacing the trimmer blade is when the hedge trimmer is not cutting properly or the blades are damaged.
All of the information in this blade replacement video is applicable to the following brands: Echo
Tools used: Two 10mm sockets, pliers, T-27 Torx bit
All of the information in this blade replacement video is applicable to the following brands: Echo
Tools used: Two 10mm sockets, pliers, T-27 Torx bit
Step By Step Instructions
1
Before you replace one or both blades on your hedge trimmer make sure the engine has cooled.
2
Next, you should remove the wire and boot from the spark plug to prevent the engine from accidentally starting.
3
We recommend wearing protective gloves when handling the trimmer blades.
4
We also recommend emptying the fuel tank.
5
Set the trimmer on its side with the muffler facing down.
6
Use two 10mm sockets to remove the locking nuts securing the trimmer blades.
7
Remove the blade guard and washers along with the tip guard.
8
Set the trimmer upside down and use a t-27 torx bit to unthread the screws securing the gear case cover.
9
With the screws unthreaded, lift off the cover.
10
Remove all the blade mounting bolts and washers.
11
Use pliers to lift out the felt seal.
12
Remove the outer spur gear and carefully lift off the lower blade.
13
Lift off the spacer plate and you can remove the upper blade. You’re now ready to install the new trimmer blade – we recommend replacing both blades at the same time.
14
Position the inner spur gear so the holes are in-line with the blade support.
15
Now align the upper blade with the sharp edge facing away from the blade support.
16
Replace the spacer plate and align the lower blade with the sharp edge facing the upper blade.
17
Replace the outer spur gear with the cam aligned on the opposite side of the inner gear cam, making sure the holes in the gear on in-line with the blades.
18
Adjust the lower blade until the gear sets into place.
19
Replace the felt seal.
20
Confirm that the gasket is in place on the gear case cover – then realign the cover and secure it with the screws.
21
With the washers intact on the mounting bolts – thread the bolts through the trimmer blades into the support. The longer bolt goes through the handle.
22
Set the trimmer on its side
23
Realign the blade guard on the mounting bolts then position the washers.
24
The manufacturer recommends using new mounting nuts to secure the blades.
25
Thread the nuts and tighten the mounting bolts.
26
Now loosen the bolts a half-turn to ensure proper blade tension.
27
Tighten the nuts to lock the bolts in place.
28
Replace the tip guard and secure it in the same way.
29
With the repair completed reattach the wire and boot to the spark plug and refill the fuel tank.
30
To ensure the hedge trimmer operates smoothly, we recommend injecting some lithium grease into the gear case.
Description
This video provides step-by-step repair instructions for replacing the trimmer blades on an Echo hedge trimmer. The most common reasons for replacing the trimmer blade is when the hedge trimmer is not cutting properly or the blades are damaged.
All of the information in this blade replacement video is applicable to the following brands: Echo
Tools used: Two 10mm sockets, pliers, T-27 Torx bit
All of the information in this blade replacement video is applicable to the following brands: Echo
Tools used: Two 10mm sockets, pliers, T-27 Torx bit
Step-By-Step Instructions
1
Before you replace one or both blades on your hedge trimmer make sure the engine has cooled.
2
Next, you should remove the wire and boot from the spark plug to prevent the engine from accidentally starting.
3
We recommend wearing protective gloves when handling the trimmer blades.
4
We also recommend emptying the fuel tank.
5
Set the trimmer on its side with the muffler facing down.
6
Use two 10mm sockets to remove the locking nuts securing the trimmer blades.
7
Remove the blade guard and washers along with the tip guard.
8
Set the trimmer upside down and use a t-27 torx bit to unthread the screws securing the gear case cover.
9
With the screws unthreaded, lift off the cover.
10
Remove all the blade mounting bolts and washers.
11
Use pliers to lift out the felt seal.
12
Remove the outer spur gear and carefully lift off the lower blade.
13
Lift off the spacer plate and you can remove the upper blade. You’re now ready to install the new trimmer blade – we recommend replacing both blades at the same time.
14
Position the inner spur gear so the holes are in-line with the blade support.
15
Now align the upper blade with the sharp edge facing away from the blade support.
16
Replace the spacer plate and align the lower blade with the sharp edge facing the upper blade.
17
Replace the outer spur gear with the cam aligned on the opposite side of the inner gear cam, making sure the holes in the gear on in-line with the blades.
18
Adjust the lower blade until the gear sets into place.
19
Replace the felt seal.
20
Confirm that the gasket is in place on the gear case cover – then realign the cover and secure it with the screws.
21
With the washers intact on the mounting bolts – thread the bolts through the trimmer blades into the support. The longer bolt goes through the handle.
22
Set the trimmer on its side
23
Realign the blade guard on the mounting bolts then position the washers.
24
The manufacturer recommends using new mounting nuts to secure the blades.
25
Thread the nuts and tighten the mounting bolts.
26
Now loosen the bolts a half-turn to ensure proper blade tension.
27
Tighten the nuts to lock the bolts in place.
28
Replace the tip guard and secure it in the same way.
29
With the repair completed reattach the wire and boot to the spark plug and refill the fuel tank.
30
To ensure the hedge trimmer operates smoothly, we recommend injecting some lithium grease into the gear case.
Applicable Product Model
Parts Needed
Blade
$28.99
Total$0.00
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com