Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairEcho Hedge Trimmer Starter Rope Replacement #P022006231
Echo Hedge Trimmer Starter Rope Replacement #P022006231
Skill Level
Total Parts Cost
$7.50Estimated Savings
$112.5004:53
- Description
This video provides step-by-step repair instructions for replacing the starter rope on an Echo hedge trimmer. The most common reasons for replacing the rope is if it is broken or trapped inside the starter assembly.
All of the information in this starter rope replacement video is applicable to the following brands: Echo
Tools used: T-27 Torx bit, flat head screwdriver
All of the information in this starter rope replacement video is applicable to the following brands: Echo
Tools used: T-27 Torx bit, flat head screwdriver
Step By Step Instructions
1
Before you replace the starter rope in your hedge trimmer make sure the engine has cooled.
2
Next, you should remove the wire and boot from the spark plug to prevent the engine from accidentally starting.
3
To reduce the chance of injury, we recommend keeping the blade cover on for this procedure.
4
Use a t-27 torx bit to unthread the screws to release the recoil starter and housing.
5
Secure the starter rope then untie the knot at the end and remove the handle.
6
Now hold the recoil starter pulley and slowly release the tension on the spring.
7
Use a phillips-head or a flat-head screwdriver to unthread the screw securing the starter pulley.
8
Carefully remove the pulley so the rewind spring stays in place underneath.
9
Be aware the spring can cause injury so use eye protection during this step.
10
Untie the knot and remove the old starter rope from the pulley.
11
Install the new starter rope by threading one end through the hole in the pulley.
12
Tie a knot at the end of the rope to secure.
13
With the knot facing down, wind the rope counter-clockwise around the pulley.
14
With the end of the rope secured in the notch align the pulley and rotate it clockwise until the pulley sets into place then rotate counter-clockwise until the spring catches onto the pulley tab.
15
Hold the pulley as you secure the screw.
16
Now rotate the pulley counter-clockwise approximately three-or-four times to put tension on the spring.
17
Align the notch in the pulley with the hole in the starter housing and feed the rope through the housing.
18
Insert the end of the rope through the handle and tie a knot to secure.
19
Make sure the knot is seated in the handle and confirm that the recoil assembly rotates freely.
20
Realign the recoil starter housing on the lower housing then thread and tighten the screws to secure.
21
The screws with the larger threads go in the bottom.
22
With the repair completed reattach the wire and boot to the spark plug and your hedge trimmer should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the starter rope on an Echo hedge trimmer. The most common reasons for replacing the rope is if it is broken or trapped inside the starter assembly.
All of the information in this starter rope replacement video is applicable to the following brands: Echo
Tools used: T-27 Torx bit, flat head screwdriver
All of the information in this starter rope replacement video is applicable to the following brands: Echo
Tools used: T-27 Torx bit, flat head screwdriver
Step-By-Step Instructions
1
Before you replace the starter rope in your hedge trimmer make sure the engine has cooled.
2
Next, you should remove the wire and boot from the spark plug to prevent the engine from accidentally starting.
3
To reduce the chance of injury, we recommend keeping the blade cover on for this procedure.
4
Use a t-27 torx bit to unthread the screws to release the recoil starter and housing.
5
Secure the starter rope then untie the knot at the end and remove the handle.
6
Now hold the recoil starter pulley and slowly release the tension on the spring.
7
Use a phillips-head or a flat-head screwdriver to unthread the screw securing the starter pulley.
8
Carefully remove the pulley so the rewind spring stays in place underneath.
9
Be aware the spring can cause injury so use eye protection during this step.
10
Untie the knot and remove the old starter rope from the pulley.
11
Install the new starter rope by threading one end through the hole in the pulley.
12
Tie a knot at the end of the rope to secure.
13
With the knot facing down, wind the rope counter-clockwise around the pulley.
14
With the end of the rope secured in the notch align the pulley and rotate it clockwise until the pulley sets into place then rotate counter-clockwise until the spring catches onto the pulley tab.
15
Hold the pulley as you secure the screw.
16
Now rotate the pulley counter-clockwise approximately three-or-four times to put tension on the spring.
17
Align the notch in the pulley with the hole in the starter housing and feed the rope through the housing.
18
Insert the end of the rope through the handle and tie a knot to secure.
19
Make sure the knot is seated in the handle and confirm that the recoil assembly rotates freely.
20
Realign the recoil starter housing on the lower housing then thread and tighten the screws to secure.
21
The screws with the larger threads go in the bottom.
22
With the repair completed reattach the wire and boot to the spark plug and your hedge trimmer should be ready for use.
Applicable Product Model
Parts Needed
Starter Rope
$7.50
Total$0.00
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com