Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairMaytag Dryer Blower Wheel Replacement #Y303836
Maytag Dryer Blower Wheel Replacement #Y303836
Skill Level
Total Parts Cost
$23.60Estimated Savings
$112.5002:48
- Description
This video provides step-by-step repair instructions for replacing the blower wheel on a Maytag dryer. The most common reasons for replacing the blower wheel are when the dryer is too hot, makes noise, takes too long, or won’t stop.
All of the information for this blower wheel replacement video is applicable to the following brands:
Maytag, Jenn Air, Caloric
Tools needed: screwdriver, pliers, snap ring pliers
All of the information for this blower wheel replacement video is applicable to the following brands:
Maytag, Jenn Air, Caloric
Tools needed: screwdriver, pliers, snap ring pliers
Step By Step Instructions
1
As with any repair, be sure you unplug the appliance before beginning.
2
Your first step is to remove the screws at the bottom of the front panel.
3
Now, rotate the panel out from the bottom to release the clips at the top.
4
Noting their location, disconnect the wires from the door switch as well as from the retaining clip on the panel and set the panel aside.
5
Release the wires from the front bulkhead.
6
Next, remove the screws to release the front bulkhead from the cabinet.
7
Remove the screws to release the blower housing cover
8
Use pliers to remove the old spring clamp and use snap ring pliers to remove the snap ring.
9
Pull the old blower wheel off.
10
Prepare to install the new blower wheel by first using a cloth to clean the motor shaft and housing.
11
Now slide the new blower wheel onto the shaft and secure it with the snap ring and the new spring clamp.
12
Make sure the new blower wheel spins freely then replace the housing cover and the screws.
13
Position the front bulkhead and secure it with the screws.
14
Secure the door switch wires on the retaining clips of both the bulkhead and the front panel then reconnect the wires to the door switch.
15
Position the front panel clips under the lip of the main top and rotate the panel into place.
16
Secure it with the mounting screws.
17
You’re now ready to plug the appliance back in to make sure it’s functioning properly.
Description
This video provides step-by-step repair instructions for replacing the blower wheel on a Maytag dryer. The most common reasons for replacing the blower wheel are when the dryer is too hot, makes noise, takes too long, or won’t stop.
All of the information for this blower wheel replacement video is applicable to the following brands:
Maytag, Jenn Air, Caloric
Tools needed: screwdriver, pliers, snap ring pliers
All of the information for this blower wheel replacement video is applicable to the following brands:
Maytag, Jenn Air, Caloric
Tools needed: screwdriver, pliers, snap ring pliers
Step-By-Step Instructions
1
As with any repair, be sure you unplug the appliance before beginning.
2
Your first step is to remove the screws at the bottom of the front panel.
3
Now, rotate the panel out from the bottom to release the clips at the top.
4
Noting their location, disconnect the wires from the door switch as well as from the retaining clip on the panel and set the panel aside.
5
Release the wires from the front bulkhead.
6
Next, remove the screws to release the front bulkhead from the cabinet.
7
Remove the screws to release the blower housing cover
8
Use pliers to remove the old spring clamp and use snap ring pliers to remove the snap ring.
9
Pull the old blower wheel off.
10
Prepare to install the new blower wheel by first using a cloth to clean the motor shaft and housing.
11
Now slide the new blower wheel onto the shaft and secure it with the snap ring and the new spring clamp.
12
Make sure the new blower wheel spins freely then replace the housing cover and the screws.
13
Position the front bulkhead and secure it with the screws.
14
Secure the door switch wires on the retaining clips of both the bulkhead and the front panel then reconnect the wires to the door switch.
15
Position the front panel clips under the lip of the main top and rotate the panel into place.
16
Secure it with the mounting screws.
17
You’re now ready to plug the appliance back in to make sure it’s functioning properly.
Applicable Product Model
Parts Needed
Blower Wheel
$23.60
Total$0.00
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com